06-09-2008
Quote:
Originally Posted by
Zim-Aix-Guru
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz
![Mad Smilie](https://www.unix.com/images/smilies/mad.gif)
Identify the adapter number in lsdev then using the adapter name run lscfg -vpl <adaptername> and read the FC adapter type. Go back to the IBM website and search for the adpater type which will the latest firmware level of your adapter. Download the firmware updaet and away you go.
9 More Discussions You Might Find Interesting
1. AIX
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Discussion started by: chlawren
8 Replies
2. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
3. UNIX for Advanced & Expert Users
Hi There,
Has anyone had any luck with or know how to get AIX 5+ to boot from a HP EVA 6000 SAN?
The servers used here will be P Class Blades
My initial searches on this so far did not bring results so I am guessing this may not be possible on HP SAN's but please let me know if I am... (0 Replies)
Discussion started by: fazzasx
0 Replies
4. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
5. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
6. AIX
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Discussion started by: filosophizer
8 Replies
7. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
8. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
9. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT CENTOS
iprupdate
IPRUPDATE(8) System Manager's Manual IPRUPDATE(8)
NAME
iprupdate - IBM Power RAID adapter/device microcode update utility
SYNOPSIS
iprupdate
iprupdate --debug --check_only --daemon --use-polling --use-uevents
DESCRIPTION
iprupdate is used to update the microcode on IBM storage adapters and the disk units attached to them to a minimum supported level. It can
be run at any time while the ipr device driver is loaded. The utility will check the microcode revision level of each storage adapter/disk
unit on the system and compare it to the microcode revision level that is installed in /etc/microcode, /usr/lib/microcode, and
/lib/firmware. If the microcode level on the adapter/device is below the minimum supported level and the level of the latest image is
newer, the microcode will be updated to the latest level available. It is desired that this be called in the boot process.
OPTIONS
--version
Print the version number of iprupdate
--debug
Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.
--check_only
Check if any adapters or disk units are below their minimum supported level.
--daemon
Run as a daemon to handle adapters and devices being hotplugged.
--use-polling
Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.
--use-uevents
Use netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
used until the first uevent notification appears, then netlink will be used.
AUTHOR
Brian King (brking@us.ibm.com)
February 2005 IPRUPDATE(8)