06-09-2008
Fibre channel drivers on RS/6000 aix 5L
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz
9 More Discussions You Might Find Interesting
1. AIX
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Discussion started by: chlawren
8 Replies
2. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
3. UNIX for Advanced & Expert Users
Hi There,
Has anyone had any luck with or know how to get AIX 5+ to boot from a HP EVA 6000 SAN?
The servers used here will be P Class Blades
My initial searches on this so far did not bring results so I am guessing this may not be possible on HP SAN's but please let me know if I am... (0 Replies)
Discussion started by: fazzasx
0 Replies
4. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
5. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
6. AIX
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Discussion started by: filosophizer
8 Replies
7. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
8. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
9. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
chs(7D) Devices chs(7D)
NAME
chs - IBM ServeRAID PCI host adapter driver
DESCRIPTION
The chs driver is the IBM ServeRAID PCI controller driver.
PRECONFIGURATION
Known Problems and Limitations
To prevent data loss, a SCSI disk drive that is not defined as part of any physical pack within a logical drive will not be accessible
through the Solaris operating environment.
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The IBM ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before booting the Solaris operating environment You use the configuration utilities to set RAID levels, stripe parameters, cache
mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/chs.conf chs configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.10 27 November 2000 chs(7D)