06-05-2008
IPMP/zones config how for this case ,urgent
Hi
I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10.
I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will help the situation.
now if I want to create 2 zones on this solaris 10 test machine and 2 network ports connected to switch from the test server , how should I configure IPMP on the test server.
What I have is,
4 IPS and 4 corresponding hostnames available ( with DNS entries) which I have to use on test machine. following info is given to me...
a.b.c.10 - machine specific hostname
a.b.c.11 - hostanme-e1000g0
a.b.c.12 - hostname-e1000g1
a.b.c.13 - application specific hostname
I wonder how to configure this test server for IPMP.
Please guide me and provide steps as it would save my time.
Current-test server
I have all4 ip-hosts entry in /etc/hosts and hostname of server is /etc/nodename = /etc/hostname.e1000g0
Thanks
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can convert a Lower case variable value to an upper case in the kron shell script. (3 Replies)
Discussion started by: dchalavadi
3 Replies
2. Shell Programming and Scripting
HELLO ALL,
URGENTLY NEEDED A SCRIPT TO SELECT AND DELETE LOWER AND MIXED CASE RECORDS FROM A COLUMN IN A TABLE.
FOR EXAMPLE : Table name is EMPLOYEE and the column name is CITY
and the CITY column records will be: Newyork
washington
... (1 Reply)
Discussion started by: abhilash mn
1 Replies
3. Solaris
Hi All,
I have unplumbed one interface.
after that ifconfig -a shows that
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (7 Replies)
Discussion started by: jegaraman
7 Replies
4. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
5. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
6. Shell Programming and Scripting
i want to get user input like this
please tell which option to chose
1. mango 2. tango 3. rango
if user chooses mango
then it should execute a set of statements and again ask like this
what do you want to do
1.add 2.subtract 3.exit
when i choose exit it should goto my previous... (1 Reply)
Discussion started by: s.deepak
1 Replies
7. Solaris
Dear All,
After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access.
IPMP works fine.
This is the error in /var/adm/messages:
sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies
8. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
9. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT CENTOS
dtest1
dtest(1) USER COMMANDS dtest(1)
NAME
dtest - simple uDAPL send/receive and RDMA test
SYNOPSIS
dtest [-P provider] [-b buf size] [-B burst count][-v] [-c] [-p] [-d] [-s]
dtest [-P provider] [-b buf size] [-B burst count][-v] [-c] [-p] [-d] [-h HOSTNAME]
DESCRIPTION
dtest is a simple test used to exercise and verify the uDAPL interfaces. At least two instantiations of the test must be run. One acts as
the server and the other the client. The server side of the test, once invoked listens for connection requests, until timing out or killed.
Upon receipt of a cd connection request, the connection is established, the server and client sides exchange information necessary to per-
form RDMA writes and reads.
OPTIONS
-P=PROVIDER
use PROVIDER to specify uDAPL interface using /etc/dat.conf (default OpenIB-cma)
-b=BUFFER_SIZE
use buffer size BUFFER_SIZE for RDMA(default 64)
-B=BURST_COUNT
use busrt count BURST_COUNT for interations (default 10)
-v, verbose output(default off)
-c, use consumer notification events (default off)
-p, use polling (default wait for event)
-d, delay in seconds before close (default off)
-s, run as server (default - run as server)
-h=HOSTNAME
use HOSTNAME to specify server hostname or IP address (default - none)
EXAMPLES
dtest -P OpenIB-cma -v -s
Starts a server process with debug verbosity using provider OpenIB-cma.
dtest -P OpenIB-cma -h server1-ib0
Starts a client process, using OpenIB-cma provider to connect to hostname server1-ib0.
SEE ALSO
dapltest(1)
AUTHORS
Arlin Davis
<ardavis@ichips.intel.com>
BUGS
uDAPL 1.2 February 23, 2007 dtest(1)