05-29-2008
MC/SG Fail to join cluster node
Hi,
Please advise me whereas I have two node cluster server configured with MC/SG. Application and DB are running on Node 1, while Node 2 is standby.
All the volume group devices are part of cluster environment. There is only one package running at node 1.
Node 2 is having the problem to join back cluster node when i issued cmrunnode at node 2 after reboot. It give some errors. I noticed the cmcluster manager and config daemons are not running at all. And, I could make sure all are part of /etc/inittab , by right it should start-up upon node 2 rebooted.
Please advise.
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello,
Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node:
# rsh <name> "command"
I have to implement this script on all the clusters of my company (a lot of...).
Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
2. HP-UX
Need help guys!
when running cmrunnode batch i'm getting this error
cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies
3. High Performance Computing
hi,
i am trying to setup a 2 node cluster environment. following is what i have;
1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10
2. 2 x HBA cards
3. 2 x Connection leads to connect ultra60 with D1000
4. 1 x D1000 storage box.
5. 3 x 9GB HDD + 2 x 36GB HDD
first of all,... (1 Reply)
Discussion started by: solman17
1 Replies
4. Solaris
I now the logical name and Virtual IP of the cluster.
How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies
5. HP-UX
Hello,
Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies
6. Solaris
Hi Gurus,
I am very new to clustering and for test i have created a single node cluster, now i want to remove the system from cluster. Did some googling however as a newbee in cluster unable to co related the info.
Please help
Thanks (1 Reply)
Discussion started by: kumarmani
1 Replies
7. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
8. UNIX for Advanced & Expert Users
Hi - Please help me to understand the Veritas Cluster fail-over capability.
We configured oracle database file system on veritas cluster file system and it is automatically failing-over from node 1 to node 2.
Does Veritas cluster softward have any option to fail-back from node 2 to node 1... (6 Replies)
Discussion started by: Mansoor8810
6 Replies
9. AIX
Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies
10. Red Hat
why does my cluster form but fail after a few minutes, or why do my multicast communications stop working after a short amount of time? (1 Reply)
Discussion started by: gema.utama
1 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)