05-29-2008
Hello,
I'm getting the following error when running "ethtool -K eth0 rx off tx off"
Cannot set device rx csum settings: Operation not supported.
Thanks in Advance.
Regards,
Aamir
10 More Discussions You Might Find Interesting
1. SCO
Does anyone know the answer to this?
When I run "sum -r" on a file that I've down loaded from the sco website, the 1st set of numbers differs from the checksum on the download page but the
2nd set matches.
If I try to install the patch, I get errors.
Anyone has an answer? (3 Replies)
Discussion started by: jn5519
3 Replies
2. Solaris
Hi Community,
Does anyone know how Disabling checksum offload on Solaris10?
Please help me, this issue is very urgent
Thank you
Have a nice day (3 Replies)
Discussion started by: Sunb3
3 Replies
3. Solaris
Anyone can tell me the different between "cksum" and "sum" command on Solaris? I read the man pages but still not get it.
And how to display the md5 checksum for a file.
Thanks, (1 Reply)
Discussion started by: redstone
1 Replies
4. Shell Programming and Scripting
I wanted a script that can give the checksum of a particular zipped file.
Can somebody help me in writing a shell script in getting the checksum of a particular tar file. (1 Reply)
Discussion started by: vkca
1 Replies
5. Shell Programming and Scripting
Hi ALL,
I use solaris OS and SFTP to get/put files from remote server.I use the below command ,
sftp user@host<<EOF
cd "dir"
get --checksum "filename"
EOF
I am getting a strange error as " get --checksum INVALID paramter". It has been working succesfully since last 3 years but all of a... (1 Reply)
Discussion started by: mohanpadamata
1 Replies
6. Shell Programming and Scripting
Hi Guys,
Sometimes, I have a problem with transferred files in ftp session. Thats why I want to produce checksum value in my local server and remote server. But I could not find anyway to produce checksum value of transferred files in remote server.
Do you have any idea?
Thanks,
Emre (3 Replies)
Discussion started by: ce_emre21
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
In file transfer with sftp protocol, what is the purpose "checksum" solves? Is this something not getting the file which has already been bought?
Waiting for your response !!! (1 Reply)
Discussion started by: sk84993
1 Replies
8. IP Networking
Hello
I am communicating with two devices using my computer over UDP protocol. The application is running fine. When I monitored the UDP traffic using Wireshark software, I found that there were too many Checksum errors.
Please find attached the png file showing this error. I am about to... (0 Replies)
Discussion started by: AustinCann
0 Replies
9. Solaris
Hi Guys,
I have about MD5 checksum so many times but I can't figure out how to use it. Can someone please show me how to perform an MD5 checksum?
Thanks a lot guys. (1 Reply)
Discussion started by: cjashu
1 Replies
10. Shell Programming and Scripting
is there a way to get a script to do a checksum on itself?
something like this:
#!/bin/sh
myexpectedsig=$(cksum $0 | awk '{print $1}')
if ; then
exit
else
who
uptime
date
fi
im looking for something that would always represent the running script, which is why im... (6 Replies)
Discussion started by: SkySmart
6 Replies
LEARN ABOUT SUSE
ifsysctl
IFSYSCTL(5) Network configuration IFSYSCTL(5)
NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) sysctl(8)
sysconfig December 2009 IFSYSCTL(5)