hi...
oh i didnīt recognized that...
ok my problem is that the prog runs (), but I really want to know what BLFīs are needed. Its because of the sw-requirement-list I have to prepare for a "customer".
Code:
FAILURES
--------
Filesets listed in this section failed pre-installation verification
and will not be installed.
Requisite Failures
------------------
SELECTED FILESETS: The following is a list of filesets that you asked to
install. They cannot be installed until all of their requisite filesets
are also installed. See subsequent lists for details of requisites.
xlC.aix61.rte 9.0.0.1 # XL C/C++ Runtime for AIX 6.1
MISSING REQUISITES: The following filesets are required by one or more
of the selected filesets listed above. They are not currently installed
and could not be found on the installation media.
bos.rte 6.0.0.0 # Base Level Fileset
bos.rte.libc 6.0.0.0 # Base Level Fileset
<< End of Failure Section >>
....
Even though there is this missing requisites the installation works. So I see no option to get a look at the required BLFs.
in win32 platform, i can easily find some GUI based ftp application like cuteFtp, WsFtp and etc which provides GUI + resuming download.
pls recommend me some similar application which runs on Sun Solaris sparc 8.
hopefully it is free.
thank you very much. (1 Reply)
First of all, excuse my ignorance in my questions, but truth is, I know nothing about Unix. I have recently purchased some A7012A's (dual port, 1000 base T/X) gigabit cards and need to use them in a windows environment.
I am trying to see if it is possible to have drivers written for the card... (0 Replies)
I am experiencing a difficulty undersatnding why my program (C++, HP UNIX) crashes. It crashes only when I build it with -O (+O2) optimization switch (used in aCC compiler). It works ok with +O0 or +O1 optimization.
Also, I see that local variables are shown incorrecly when program is built... (3 Replies)
Hi,
I am trying to use either awk or sed to drop the first two folders in a path. So if I had path /folder1/folder2/folder3/folder4.... I need to drop folder1&2, so the new path would be /folder3/folder4...
If folder1 and folder2 were the same all the time, this would be easy. But... (4 Replies)
Is there any book/resource that one can refer to, to be able to write programs at kernel/system level.. I'm looking for a programming book that could serve as a guide to write kernel codes / system level programming etc..
I have Tannenbaum's Design and Implementation. It addresses theoretical... (2 Replies)
I need to install "bos.loc.utf.EN_US" in AIX ( version 6100-06-05-1115). I found the right bff U845493 and I smitty to install it and encountered the "missing requisites" error in which missing the "base level fileset" . And I couldn't find this fileset from the Internet for long.
Do any one able... (2 Replies)
I need to install "bos.adt.debug" in AIX ( version 6100-06-05-1115). I found the right bff U818918 and I smitty to install it and encountered the "missing requisites" error as attached in which missing the "base level fileset" bos.adt.debug 6.1.0.0. And I couldn't find this fileset from the... (3 Replies)
Hey Friends, its me again! :o
I was asked to create a script that would go into our backup directories and delete/purge anything in the directory after a certain amount of days, normally I would be able to write something up that goes to the directory finds it and deletes it.
cd... (12 Replies)
Hello gurus, this should be simple but I cant seem to figure this out. Please assist.
I have several thousand zip files in a directory
A.ZIP
B.ZIP
.
.
..
Z.ZIP
All these zipped files have a single subdirectory at level1 and then other files and folders under the subdirectory.
... (3 Replies)
Hi All,
we have a requirement to split a content in a text file every 5 rows and write in a new file .
conditions:
if 5th line falls between center of the statement . it should look upto after ";"
files are below format:
1 UPDATE TABLE TEST1 SET VALUE ='AFDASDFAS'
2 WHERE... (3 Replies)
Discussion started by: KK230689
3 Replies
LEARN ABOUT DEBIAN
magick
GraphicsMagick-Config(1) General Commands Manual GraphicsMagick-Config(1)NAME
GraphicsMagick-config - get information about the installed version of GraphicsMagick
SYNOPSIS
GraphicsMagick-config [--cflags] [--cppflags] [--exec-prefix] [--ldflags] [--libs] [--prefix] [--version]
DESCRIPTION
GraphicsMagick-config prints the compiler and linker flags required to compile and link programs that use the GraphicsMagick Application
Programmer Interface.
EXAMPLES
To print the version of the installed distribution of GraphicsMagick, use:
GraphicsMagick-config --version
To compile a program that calls the GraphicsMagick Application Programmer Interface, use:
cc `GraphicsMagick-config --cflags --cppflags --ldflags --libs` program.c
OPTIONS --cflags
Print the compiler flags that are needed to use the GraphicsMagick C interface. (Usually empty.)
--cppflags
Print the preprocessor flags that are needed to find the GraphicsMagick C include files and defines to ensure that the GraphicsMag-
ick data structures match between your program and the installed libraries.
--exec-prefix
Print the directory under which target specific binaries and executables are installed.
--ldflags
Print the linker flags that are needed to link with the GraphicsMagick library.
--libs Print the linker flags that are needed to link a program with libGraphicsMagick.
--version
Print the version of the GraphicsMagick distribution to standard output.
COPYRIGHT
Copyright (C) 2002 GraphicsMagick Group
Copyright (C) 2002 ImageMagick Studio
AUTHORS
Bob Friesenhahn
GraphicsMagick 4 December 2002 GraphicsMagick-Config(1)
05-28-2008
), but I really want to know what BLFīs are needed. Its because of the sw-requirement-list I have to prepare for a "customer".