05-25-2008
What Linux distribution should I use?
Hey
I am right now working on an old Compaq computer, and because I have a newer one I thought of installing Linux on this one. The thing is that I don't know which Linux distribution that would work with a minimum of lag. My computer specifications is:
Compaq Presario 7000
Intel Pentium III-processor
999MHz, 384 MB RAM
Any suggestions?
Sixmax
7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I m working on many Linux servers in my project. But i am unable to know which Linux Distribution i am using Like whether i am using SUSE or REDHAT or MONDRAKE. I tried with "uname" command. But it does not help me. Please provide me the command if u know.
Regards,
Basavaraja KC (3 Replies)
Discussion started by: BasavarajaKC
3 Replies
2. Shell Programming and Scripting
Hi,
I m working on many Linux servers in my project. But i am unable to know which Linux Distribution i am using Like whether i am using SUSE or REDHAT or MONDRAKE. I tried with "uname" command. But it does not help me. Please provide me the command if u know.
Regards,
Basavaraja KC (5 Replies)
Discussion started by: BasavarajaKC
5 Replies
3. Programming
Hi,
Can anyone please tell me, what is the best Linux distribution for Software Development.
Thanks,
Philip. (4 Replies)
Discussion started by: Phi01
4 Replies
4. Linux
Hi
I consider changing operating system onto Linux. But I'm not sure what kind of distribution should I use :
- Red Hat
- Suse
- Ubuntu
- Debian
- Fedora
Operating system will be operating on the notebook to replace Win XP and must be stable version with all drivers to hardware (WiFi... (7 Replies)
Discussion started by: presul
7 Replies
5. Linux
Dear all
i am new to Linux, i need a Linux OS that have been "qt development and lesstif" together.
Regards (5 Replies)
Discussion started by: mkhorami76
5 Replies
6. Fedora
Hi,
i'm currently part of an apprenticeship becoming a IT specialist.
Because I'm already an electronic technician (finished apprenticeship) I can do this one in 2 years (normally you need 3).
Thing is, in school they started out with basic unix stuff (working with the shell) in the first... (3 Replies)
Discussion started by: Dr. Nick
3 Replies
7. What is on Your Mind?
What was the first Linux distribution you tried?
My first was Knoppix, it was pretty good I thought, and it supported my old hardware http://www.linuxforum.com/images/smilies/smile.png Too bad I couldn't figure out how to install it at the time though.
What about you? (32 Replies)
Discussion started by: billcrosby
32 Replies
IDA(4) BSD Kernel Interfaces Manual IDA(4)
NAME
ida -- Compaq Intelligent Drive Array Controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ida
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ida_load="YES"
DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives
into one or more high-performance logical drives. The drive array is managed by an array controller.
These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical
drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface.
HARDWARE
The following controllers are supported by the ida driver:
o Compaq SMART Array 221
o Compaq Integrated SMART Array Controller
o Compaq SMART Array 4200
o Compaq SMART Array 4250ES
o Compaq SMART 3200 Controller
o Compaq SMART 3100ES Controller
o Compaq SMART-2/DH Controller
o Compaq SMART-2/SL Controller
o Compaq SMART-2/P Controller
o Compaq SMART-2/E Controller
o Compaq SMART Controller
IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause
hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by
Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 8, 2004 BSD