05-23-2008
you should have lputil pkg installed. If yes, do /usr/sbin/lpfc/lputil
you will get a menu like this and you can get relative info.
LightPulse Common Utility for Solaris/SPARC. Version 2.0a5 (4/7/2005).
Copyright (c) 2005, Emulex Corporation
Emulex Fibre Channel Host Adapters Detected: 2
Host Adapter 0 (lpfc2) is an LP10K (Ready Mode)
Host Adapter 1 (lpfc3) is an LP10K (Ready Mode)
MAIN MENU
1. List Adapters
2. Adapter Information
3. Firmware Maintenance
4. Reset Adapter
5. Persistent Bindings
0. Exit
10 More Discussions You Might Find Interesting
1. Solaris
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies
2. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
3. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
4. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
5. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
6. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
7. Solaris
Hello,
I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as:
HBA Model Name
HBA Firmware version
HBA Port details
HBA Driver details
First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies
8. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
9. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
10. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT DEBIAN
ql-hba-snapshot
ql-hba-snapshot(8) System Administration ql-hba-snapshot(8)
NAME
ql-hba-snapshot - display specific information of the QLogic HBA.
SYNOPSIS
ql-hba-snapshot <Host number> [OPTIONS]
DESCRIPTION
FC HBA Snapshot Utility
This utility displays the details of the QLogic HBA attached to the system. It uses one of the two file systems for scanning: proc or
sysfs.
<Host number> | <-a/--all> [optional]
Provide the <HOST NUMBER> to display the detailed information of the HBA. With no option specified, general information of all
hosts will be displayed. Ex. # /usr/sbin/ql-hba-snapshot <Host Number> # /usr/sbin/ql-hba-snapshot --procfs <Host Number> (For
procfs)
-h, --help
Prints the help message. Ex. # /usr/sbin/ql-hba-snapshot --help
-hl, --hostlist
This option displays the list of QLogic hosts (HBAs) connected to this system. The <HOST NUMBER> can be obtained by using following
command Ex. # /usr/sbin/ql-hba-snapshot --hostlist
-p, --parameters
This option displays the command line parameters that can be passed to the QLogic HBA driver. Ex. # /usr/sbin/ql-hba-snapshot
--parameters <Host Number>
-s, --statistics
This option displays the statistical information for specified host. Stastics option is only supported in "sysfs" based scan. Ex.
# /usr/sbin/ql-hba-snapshot --statistics <Host number/--all>
-proc, --procfs
This options forces the the utility to scans information based on "procfs", instead of default sysfs. Ex. # /usr/sbin/ql-hba-snap-
shot --procfs [Other valid option]
-v, --verbose
This enables verbose display. The detailed information of LUNs will be displayed in addition to standard one. This option is only
supported in sysfs. Ex. # /usr/sbin/ql-hba-snapshot --verbose <Host number/-a>
SEE ALSO
ql-dynamic-tgt-lun-disc(8), ql-lun-state-online(8), ql-set-cmd-timeout(8)
Matthias Schmitz <matthias@sigxcpu.org> July 2009 ql-hba-snapshot(8)