|
|
Sponsored Content
Operating Systems
Solaris
One StorageTek 6140 vs Two (2) 2540 's?
Post 302197165 by buddhavelvet on Tuesday 20th of May 2008 09:36:13 AM
05-20-2008
Thanks for the information lowbyte 
Is it safe to assume then that two 2540's would perform 200 KIOPs, ca. 1200 MB/s ? I'm trying to compare the performance of two 2540's vs one 6140.
Two fully populated 2540's (24x73 15Krpm) is going to cost roughly $15k, while one fully populated 6140 price is around $27k.
Thanks again.
-bv
Is it safe to assume then that two 2540's would perform 200 KIOPs, ca. 1200 MB/s ? I'm trying to compare the performance of two 2540's vs one 6140.
Two fully populated 2540's (24x73 15Krpm) is going to cost roughly $15k, while one fully populated 6140 price is around $27k.
Thanks again.
-bv
|
|
8 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Filesystems, Disks and Memory
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Discussion started by: Sapfeer
3 Replies
3. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
4. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
5. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
6. Hardware
Hi all,
My Sun StorageTek 2540 have redundant batteries, but a battery was failed.
# /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru
Name FRU Alarm State Status Revision Unique Id
-------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies
7. Hardware
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies
8. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
LEARN ABOUT CENTOS
bonds
Bonds(1) General Commands Manual Bonds(1) NAME
Bonds - Example of bond pricing SYNOPSIS
Bonds DESCRIPTION
Bonds is an example of using QuantLib. It shows how to set up a term structure and then price some simple bonds. The last part is dedicated to peripherical computations such as yield-to-price or price-to-yield. SEE ALSO
The source code Bonds.cpp, BermudanSwaption(1), CallableBonds(1), CDS(1), ConvertibleBonds(1), DiscreteHedging(1), EquityOption(1), Fitted- BondCurve(1), FRA(1), MarketModels(1), Replication(1), Repo(1), SwapValuation(1), the QuantLib documentation and website at http://quantlib.org. AUTHORS
The QuantLib Group (see Authors.txt). This manual page was added by Luigi Ballabio . QuantLib 22 October 2008 Bonds(1)