05-16-2008
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
is there anu way by which i can find out if all the disks on the system are working ?
Milind Shauche. (2 Replies)
Discussion started by: shauche
2 Replies
2. HP-UX
I am new to being a Unix admin and have a question about replacing some hardware. I have a K class box using HP-UX 10.20 with three disks. Two of the drives are in one logical volume. Every 3 or 4 days, the syslog is showing that one of these drives is experiencing "POWERFAILED" and then recovering... (6 Replies)
Discussion started by: SemiOfCol
6 Replies
3. Filesystems, Disks and Memory
Hi people,
I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to... (2 Replies)
Discussion started by: christopher4
2 Replies
4. Solaris
hi all,
have a solaris 9 OS and a SAN disk which used to work fine is not getting picked up by my machine. can anyone point out things to check in order to troubleshoot this ??
thanks in advance. (3 Replies)
Discussion started by: cesarNZ
3 Replies
5. Red Hat
in red hat 4, 5 any one know any commands or any scritps to monitor HP DL 380 G5/6 server and trigger alarm when hard disk failed.
thanks for all support
---------- Post updated at 02:45 PM ---------- Previous update was at 12:00 PM ----------
does HP ProLiant Support Pack support is... (4 Replies)
Discussion started by: maxlee24
4 Replies
6. Solaris
Hello guys,
I have two servers performing the same disk operations. I believe one server is having a disk's impending failure however I have no hard evidence to prove it. This is a pair of Netra 210's with 2 drives in a hardware raid mirror (LSI raid controller). While performing intensive... (4 Replies)
Discussion started by: s ladd
4 Replies
7. UNIX for Advanced & Expert Users
Hi there,
Don't know if my title is relevant but I'm dealing with dangerous materials that I don't really know and I'm very afraid to mess anything up.
I have a Debian 5.0.4 server with 4 x 1TB hard drives.
I have the following mdstat
Personalities :
md1 : active raid1 sda1 sdd1... (3 Replies)
Discussion started by: chebarbudo
3 Replies
8. AIX
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
Discussion started by: garethr
1 Replies
9. Ubuntu
Does anyone know what is solution for this error ?tar: Exiting with failure status due to previous errors from last 3 days I am trying to take backup of home/user directory getting again and again same error please anyone give me solution (8 Replies)
Discussion started by: Akshay Hegde
8 Replies
10. AIX
Hi all,
I have encountered the issue with the hard disk, the disk is failed and need to replace by the new one.
As my understanding, this is just to take out the failed disk and insert the new ones, and that's all.
But the third party hardware vendor said, there should be another procedure... (9 Replies)
Discussion started by: Phat
9 Replies
LEARN ABOUT LINUX
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)