Sponsored Content
Operating Systems AIX ibm san cache battery with aix Post 302195727 by dukessd on Thursday 15th of May 2008 07:40:29 PM
Old 05-15-2008
The DS should also post errors when the cache is off line.
Do you have the rdac drivers installed correctly?
I don't know because I do not use DS storage, but should there be a health check job in cron like the SSA drivers use?
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

First steps on Ibm SAN DS4500

Hello everyone ! Im new on Ibm San DS4500. Can you give me some tips to this, because I dont want to make a mistake. I have some questions. How can I know how much space get on the san, I cant find it. How can add more space to a partition. Do you have some tutorial about this. I... (0 Replies)
Discussion started by: lo-lp-kl
0 Replies

2. AIX

Question about IBM San Ds4500

I have a question about SAN commands I have almost 15Tb of disk on my san but assigned and something else I have almost 11Tb There is a command to know, what its my real total storage capacity and another command to know how much I used .? Thanks again in advance (0 Replies)
Discussion started by: lo-lp-kl
0 Replies

3. AIX

IBM AIX on IBM Eseries & x series server

Hi, I want to know whether IBM AIX can be installed on the IBM e series and x series server hardware? Thanks & Regards Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies

4. Solaris

Sunfire 490 connect to IBM SAN DS4000

Hi All Recently i plan use our company Sunfire V490 to hook up the IBM SAN Storage DS4000. But i not sure is it got any requirement to do this, is it need any extra driver, equipment??? hope can get some advice from here.. Kindly advise. Thanks all (3 Replies)
Discussion started by: SmartAntz
3 Replies

5. Solaris

Cannot see the IBM SAN storage

HI all, I had recently change the Server storage from EMC to the IBM SAN. but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server. When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies

6. AIX

IBM SAN storage -- cache battery

Hello, I have IBM SAN STORAGE DS4100 and one of the cache battery for the controller is dead. Suddenly the performance has been degraded and access to SAN disks ( reading and writing ) became very slow ? My query: Replacing the battery will take 6 days, so in the mean time what are the ways... (1 Reply)
Discussion started by: filosophizer
1 Replies

7. AIX

Help: Disable write cache for battery replacement

Hello Everyone, I have a AIX 5.2 and saw the following entry in the error report in one of my servers. IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION FFDFB692 0705111911 P H sisraid0 BATTERY PACK FAILURE Now, we're ready to replace the battery pack but I heard I need to... (0 Replies)
Discussion started by: blakedaddy
0 Replies

8. AIX

IBM SAN TO SAN Mirroring

Has anyone tried SAN to SAN mirroring on IBM DS SAN Storage. DS5020 mentions Enhanced Remote Mirror to multi-LUN applications I wonder if Oracle High availibility can be setup using Remote Mirror option of SAN ? (1 Reply)
Discussion started by: filosophizer
1 Replies

9. AIX

IBM AIX - SAN Storage DS4300 issue

Hi, This is follow up to the post https://www.unix.com/aix/233361-san-disk-appearing-double-aix.html When I connected Pseries Machine HBA Card ( Dual Port ) directly to the SAN Storage DS4300 , I was able to see Host Port Adapter WWN numbers , although I was getting this message... (2 Replies)
Discussion started by: filosophizer
2 Replies

10. AIX

IBM AIX Internal HDD vs SAN HDD and Oracle

Hi Folks, I am facing an issue with the performance. P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
gnutls_x509_crt_get_subject_alt_name(3) 			      gnutls				   gnutls_x509_crt_get_subject_alt_name(3)

NAME
gnutls_x509_crt_get_subject_alt_name - API function SYNOPSIS
#include <gnutls/x509.h> int gnutls_x509_crt_get_subject_alt_name(gnutls_x509_crt_t cert, unsigned int seq, void * san, size_t * san_size, unsigned int * critical); ARGUMENTS
gnutls_x509_crt_t cert should contain a gnutls_x509_crt_t structure unsigned int seq specifies the sequence number of the alt name (0 for the first one, 1 for the second etc.) void * san is the place where the alternative name will be copied to size_t * san_size holds the size of san. unsigned int * critical will be non-zero if the extension is marked as critical (may be null) DESCRIPTION
This function retrieves the Alternative Name (2.5.29.17), contained in the given certificate in the X509v3 Certificate Extensions. When the SAN type is otherName, it will extract the data in the otherName's value field, and GNUTLS_SAN_OTHERNAME is returned. You may use gnutls_x509_crt_get_subject_alt_othername_oid() to get the corresponding OID and the "virtual" SAN types (e.g., GNUTLS_SAN_OTHERNAME_XMPP). If an otherName OID is known, the data will be decoded. Otherwise the returned data will be DER encoded, and you will have to decode it yourself. Currently, only the RFC 3920 id-on-xmppAddr SAN is recognized. RETURNS
the alternative subject name type on success, one of the enumerated gnutls_x509_subject_alt_name_t. It will return GNUTLS_E_SHORT_MEM- ORY_BUFFER if san_size is not large enough to hold the value. In that case san_size will be updated with the required size. If the cer- tificate does not have an Alternative name with the specified sequence number then GNUTLS_E_REQUESTED_DATA_NOT_AVAILABLE is returned. REPORTING BUGS
Report bugs to <bug-gnutls@gnu.org>. General guidelines for reporting bugs: http://www.gnu.org/gethelp/ GnuTLS home page: http://www.gnu.org/software/gnutls/ COPYRIGHT
Copyright (C) 2012 Free Software Foundation, Inc.. Copying and distribution of this file, with or without modification, are permitted in any medium without royalty provided the copyright notice and this notice are preserved. SEE ALSO
The full documentation for gnutls is maintained as a Texinfo manual. If the info and gnutls programs are properly installed at your site, the command info gnutls should give you access to the complete manual. As an alternative you may obtain the manual from: http://www.gnu.org/software/gnutls/manual/ gnutls 3.1.15 gnutls_x509_crt_get_subject_alt_name(3)
All times are GMT -4. The time now is 07:44 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy