Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: hp-ux 10.20 boot issue
Operating Systems HP-UX hp-ux 10.20 boot issue Post 302195526 by davel1000 on Thursday 15th of May 2008 09:45:56 AM
Old 05-15-2008
hp-ux 10.20 boot issue
Hello, have HP Visualize C3600 workstation. Issue is as follows:

When I attempt to boot, unit will not boot successfully and will halt at a menu, the same menu as when during a boot one hits any key within 10 seconds to discontinue. When I attempt to boot with Boot primary, both with IPL interaction and not, system shows following:

Booting ... Boot IO dependent code (IODC) revision 0
IPL error: bad LIF magic: not a valid LIF volume.
Error reading IPL.

and goes back to menu.

From menu:
When I do a path primary system shows Primary Boot Path: FWSCSI.6.0
When I do a path alternate system shows Alternate Boot Path: SCSI.6.0

In configuration portion of menu, when I do a search IPL system shows following:

Search for device(s) with bootable media ...
No devices found.

Prior to this issue when I did a search IPL system would show Path# P0, Device Path FWSCSI.6.0, Device Type & Untilities HP36.4GMAN3367MC (which I assume is the hard drive) and IPL

Since I cannot use boot primary with IPL interaction to attempt to debug issue, as system returns to menu, what is next step?

This is a very high priority. Expeditious response is needed and appreciated.

DJ
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

boot up issue

Could somone please tell me what happened when I reboot my computer, it take too long to pass the part it said "starting sendmail" I only changed the server name and when I reboot the server, all of the services are running except when it got to : starting sendmail it take toooo long to... (1 Reply)
Discussion started by: lapnguyen
1 Replies

2. UNIX for Advanced & Expert Users

Dual boot issue

Hi All, 1st HDD is loaded with Windows 2000 Professional and I have installed Red Hat ES 3.0 on second HDD(80GB). After linux installation failed to load windows and boot stucks with displaying only L How to fix this issue Thanks in advance for your valuable answer. Regards, Bachegowda (1 Reply)
Discussion started by: bache_gowda
1 Replies

3. HP-UX

PXE boot port issue

Hi,all: I want to boot an IA unix box from network, I am sure I set the DHCP and boot server, but it still failed ! It says : Client MAC Address: 00 18 FE 28 91 82 .....- PXE-E16: Valid PXE offer not received. Load of Core LAN Gb A failed: Not Found I use the nettl command to trace the UDP... (0 Replies)
Discussion started by: bluepluto
0 Replies

4. Solaris

boot-archive issue

I had logged into Server via ALOM and was placed into runlevel 5 other than 3 which is default. I did a svcadm delete boot-archive, and was promptly placed in runlevel 3. Now, I am unable to do a telnet or login into the server through any other service. bash-3.00# svcs -a svcs -a STATE ... (3 Replies)
Discussion started by: praveenr
3 Replies

5. Solaris

Solaris-RHEL5 Dual boot issue

Machine: x86 OS : Dualboot Solaris and RHEL5 -Solaris 10 in first fdisk partition. RHEL5 - /boot in partition2 / in partition3 swap in 1st... (1 Reply)
Discussion started by: saagar
1 Replies

6. Red Hat

Dual boot issue .....

Hi, I have a laptop with two os running in it, Windows XP & RHEL5. Accidentally, we have deleted the windows entry in grub.conf file. Later we connected the hard disk of laptop to another system & deleted the linux partitions from the disk management tool of windows. Now the issue is, the... (7 Replies)
Discussion started by: Amol21
7 Replies

7. Solaris

Boot parameter issue

Hi all i have an issue when i change auto-boot?=false and reboot it again it is going to auto-boot?=true can any one tell that what should i do for auto-boot?=false for permanently thank you in advance (11 Replies)
Discussion started by: wkbn86
11 Replies

8. Solaris

Persistent boot disks issue

Hi all, please i need your help urgently I am faced to a serious boot disks issue on an Sun Fire E2900. The system run with two disque in zpool . The operating system is Solaris 10 (ZFS) The first time the issue occured, i got the error below on the two disks: Apr 7 08:04:33... (0 Replies)
Discussion started by: saki_jumeau
0 Replies

9. Solaris

V100 boot issue

In the server room at my new job, there is a V100 with a problem. When power is turned on, the machine goes to the lom prompt. Entering poweron yields an endless supply of this message with no way to break out of it. ********************************************** PSTATE=0000000000000015... (3 Replies)
Discussion started by: chilinski
3 Replies

10. SCO

Issue during boot

Hi, I am using SCO OpenServer 5 During boot I get this message: PANIC: HTFS: Bad directory ino 2 (offset 0) on HTFS dev hd (1/42) Cannot dump 8095 pages to dumpdev hd (1/41): Space for only 0 pages Dump not completed How can I fix this? I have no boot/root floppy. If it is a "disk... (8 Replies)
Discussion started by: nubian_sundance
8 Replies

LEARN ABOUT X11R4

bootctl

BOOTCTL(1)							      bootctl								BOOTCTL(1)

NAME

       bootctl - Control the firmware and boot manager settings

SYNOPSIS

       bootctl [OPTIONS...] status

       bootctl [OPTIONS...] list

       bootctl [OPTIONS...] update

       bootctl [OPTIONS...] install

       bootctl [OPTIONS...] remove

DESCRIPTION

       bootctl checks, updates, installs or removes the boot loader from the current system.

       bootctl status checks and prints the currently installed versions of the boot loader binaries and all current EFI boot variables.

       bootctl list displays all configured boot loader entries.

       bootctl update updates all installed versions of systemd-boot, if the current version is newer than the version installed in the EFI system
       partition. This also includes the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is
       created if there is no current entry. The created entry will be added to the end of the boot order list.

       bootctl install installs systemd-boot into the EFI system partition. A copy of systemd-boot will be stored as the EFI default/fallback
       loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created and added to the top of the boot order list.

       bootctl remove removes all installed versions of systemd-boot from the EFI system partition, and removes systemd-boot from the EFI boot
       variables.

       If no command is passed, status is implied.

OPTIONS

       The following options are understood:

       -h, --help
	   Print a short help text and exit.

       --version
	   Print a short version string and exit.

       --path=
	   Path to the EFI System Partition (ESP). If not specified, /efi, /boot, and /boot/efi are checked in turn. It is recommended to mount
	   the ESP to /boot, if possible.

       -p, --print-path
	   This option modifies the behaviour of status. Just print the path to the EFI System Partition (ESP) to standard output and exit.

       --no-variables
	   Do not touch the EFI boot variables.

EXIT STATUS

       On success, 0 is returned, a non-zero failure code otherwise.

SEE ALSO

       Boot loader specification[1] systemd boot loader interface[2]

NOTES

	1. Boot loader specification
	   https://www.freedesktop.org/wiki/Specifications/BootLoaderSpec

	2. systemd boot loader interface
	   https://www.freedesktop.org/wiki/Software/systemd/BootLoaderInterface

systemd 237																BOOTCTL(1)
All times are GMT -4. The time now is 09:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy