05-12-2008
Mounting a disk drive that you want to save data on.
It's not a striaght forward action as just mounting the drive - SCO has no SCSI mount information so the drive has to be configured in SCO SCSI tables before you can access it. It's a rather complicated procedure.
SCO site has a technical document regarding this. TA# 104863
It is intitled " How do I add a SCSI or IDE disk that has data I want to keep? "
It has step by step instructions for adding a drive.
Here is a direct link to the relevent document.
How do I add a SCSI or IDE disk that has data I want to keep?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. Solaris
Hi Friends,
I am using VMware 6.0 and i want to transfer some files from External HDD so how to mount the Disk, and i am not able to assign any ip to my network card any one can help me how to set ip in VMware.
Thanks and Regards,
Venky.:b: (0 Replies)
Discussion started by: 1409.venkatesh
0 Replies
5. Windows & DOS: Issues & Discussions
Hi,
Unix based,
My harddrive won't boot and I'm looking for a reliable tool
that can mount a hdd on Windows XP and show me the files
stored on a NFS system.
I tried the tool: Ext2IFS but this didn't work.
I found a lot of tools on google to mount nfs share thru a network
but that's... (1 Reply)
Discussion started by: severt
1 Replies
6. Filesystems, Disks and Memory
I started on another thread and full story can be seen here: https://www.unix.com/security/91428-how-reset-root-password-old-unix-system-v.html
But my situation turned to land on this thread now.
I have old scsi HDD out of the UHC UNIX System V Rel. 4.0 Version 3.6 box. And need to read... (1 Reply)
Discussion started by: 82026
1 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. Solaris
I just installed Solaris 11.2 - and it is a bugger. How do I mount an extra HDD that is now formated to NTFS through gparted
it keeps telling me I don't have any ntfs on this laptop. it has two hdds, /dev/sda1 /dev/sdb1 (Linux lingo) Solaris is installed on primary hard drive back of it. then... (2 Replies)
Discussion started by: userx-bw
2 Replies
9. Fedora
once again, mounting another volume or hdd the fstab-file is giving me a headache. May someone could give me a hint how to configure the fstab-file properly to use the hdd.
The following
ls -l /dev/disk/by-uuidis giving me this
Thats the UUID for /dev/sdb1 with the name "save"... (6 Replies)
Discussion started by: 1in10
6 Replies
10. Emergency UNIX and Linux Support
rying it this way, because I can't handle the slices for the second hdd. If there is someone on this forum who can help me out of that misery, he would really save my digital life in this digital ocean.
So not giving up, reading several times the manual of gpart. But the best hint in all that... (0 Replies)
Discussion started by: 1in10
0 Replies
SD(4) Linux Programmer's Manual SD(4)
NAME
sd - driver for SCSI disk drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */
#include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIGURATION
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
+3 partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a reread of the SCSI disk partition tables. No parameter is needed.
The SCSI ioctl(2) operations are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl(2) fails with
the error EINVAL.
FILES
/dev/sd[a-h]
the whole device
/dev/sd[a-h][0-8]
individual block partitions
COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the
latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux 2017-09-15 SD(4)