05-06-2008
Are you talking about duplex printing?
Assuming the printer is properly set up using the correct driver, there should be options for this in smit printer. There are also options to indicate which paper drawer to use, etc.
6 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi guys and gir.. emm
hey guys! (only kidding girls)
I have been asked to provide a tutorial on how to perform an automatic back up (to tape) for 23 sun sparc workstations networked using an ethernet setup under the UNIX operating system.
Sounds easy enough to you... I've never ever seen... (4 Replies)
Discussion started by: maross
4 Replies
2. UNIX for Dummies Questions & Answers
Can Anyone Be Any Assistance To Help A New User Get His Back-up Commands Defined Along With Other Useful Information On Viewing What's On Tapes And Restoring Data From The Tapes. (0 Replies)
Discussion started by: ricjoh
0 Replies
3. IP Networking
Hi every body,
Is it possible to connect two servers Back-to-Back (Point-to-Point) using HBA adapters & using Fiber.
Note it is direct connection & there is no switches between the servers.
I'm concern about using HBA adapters, it is possible or not.
Thanks in advance. :) (3 Replies)
Discussion started by: aldowsary
3 Replies
4. UNIX for Dummies Questions & Answers
Hi,
Can any one tell me how to restore back the deleted file in unix?
I know the file name.
If i know the inode number of the file does help more to restore back the file? (1 Reply)
Discussion started by: siba.s.nayak
1 Replies
5. UNIX for Dummies Questions & Answers
i had this unix korn shell code that connects to oracle database and execute the oracle procedure. i need to add a variable that indicates the oracle procedure failed. basically the variable is to check if the oracle procedure failed it will assign 1 and when the variable is equal to 1 it will not... (4 Replies)
Discussion started by: wtolentino
4 Replies
6. UNIX for Dummies Questions & Answers
Howdy all,
I'm new on this great forum. In 1990 I did a course UNIX system admin. I remember that we used a minicomputer with 15 terminals. My question is..what were the hardware requirements those days to install UNIX Sys 5 R 4? I guess most modern PC's are more powerfull then the... (2 Replies)
Discussion started by: raylier
2 Replies
GPR(1) General Commands Manual GPR(1)
NAME
gpr - a graphical frontend for lpr.
SYNOPSIS
gpr [-h] [--help] [-P <printer>] [-J <job name>] [-r] [-n] [-p <flag>] [filename]...
DESCRIPTION
gpr is a graphical interface to lpr that provides for easy configuration of printer-specific options. gpr interfaces with a PostScript
printer's PPD file to create a user-interface of configurable options. Based upon user choice, the device-specific option code is then
inserted into the PostScript job and sent to the printer. This can be used to tell the printer to duplex or staple the print job, or tell
it what paper tray to draw paper from. NOTE: gpr will detect if the file to be print is postscript, and, if not, it will call a2ps to pre-
process it before sending it to ppdfilt and to lpr.
OPTIONS
gpr accepts the following options:
-h, --help
Show summary of options.
-P Specify a destination printer
-d Enable debugging output
-J lpr option: Job name to print on burst page
-r lpr option: Remove the files upon completion of spooling
-n gpr option: Print the command line rather than executing the command
-p
gpr option: Use ppdfilt: 0 = Never, 1 = Always, 2 = with non-default PPD
OTHER INFO
The webpage for the GNULpr suite is at http://lpr.sf.org.
SEE ALSO
lpr(1),
GPR(1)