05-01-2008
Well, indeed everything should turn off when you reboot your server ...
Seems like you mean: "It doesn't come up again after reboot."
Probably you simply haven't configured it to get an IP address and so an at system startup. Have a look at your system's documentation regarding startup and networking.
10 More Discussions You Might Find Interesting
1. Solaris
Hi Guru's
Can any want here could explain to me the different between soft reboot and hard reboot .
Best Regards
Seelan (3 Replies)
Discussion started by: seelan3
3 Replies
2. UNIX for Dummies Questions & Answers
I just installed Crux on my laptop, which means I'll have to configure /etc/rc.d/net to adapt to my wireless internet. When I ran Linux before, I connected through eth1. How should I configure the /etc/rc.d/net file accordingly?
Thanks for reading,
Octal. (0 Replies)
Discussion started by: Octal
0 Replies
3. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
4. Solaris
Hi Guys,
I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets. (1 Reply)
Discussion started by: kurva
1 Replies
5. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
6. UNIX for Dummies Questions & Answers
Hello folks;
I have a NIC card on my SUSE 10.3 server with eth0 & eth1 configured with two IP addresses (172.16.5.3 & 172.16.5.4)
I'd like to remove the IP assigned to eth1 (172.16.5.4). i think i know i can go into ifcfg-eth1 and edit it but before i do that, i want to know if there's a better... (2 Replies)
Discussion started by: Katkota
2 Replies
7. UNIX for Advanced & Expert Users
Hey everyone. We're in the process of deploying a number of servers. They're HP DL360 G6's. OS is RHEL 5.4
They've got two on board NIC's, as well as an additional dual port network card, giving us a total of 4 NIC's. Eth0 and Eth2 are bonded together using the bonding module, and the resulting... (2 Replies)
Discussion started by: msarro
2 Replies
8. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
9. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
10. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
reboot(8) System Manager's Manual reboot(8)
NAME
reboot - Restarts the machine
SYNOPSIS
/usr/sbin/reboot [-dlnq]
DESCRIPTION
When the system is running and multiple users are logged in, use the shutdown -r command to perform a reboot operation. If no users are
logged in, use the reboot command.
The reboot command normally stops all running processes, syncs the disks, logs the reboot, and writes a shutdown entry in the login
accounting file, /var/adm/wtmp.
The reboot command uses the sync call to synchronize the disks, and to perform other shutdown activities such as resynchronizing the hard-
ware time-of-day clock. After these activities, the system reboots. By default, the system starts and the file systems are automatically
checked. If the start-up activities are successful, the system comes up in the default run-level.
You must have root privileges to use this command. Using the -n flag can result in file system damage.
FLAGS
Generates a crash dump of the system before halting it. Can be used with any of the other flags. Does not log the reboot using syslog
Does not sync the disks or log the reboot using syslog Performs a quick reboot without first shutting down running processes; does not log
the reboot using syslog
EXAMPLES
To enable the default reboot action, enter: reboot This command causes the system to stop all running processes, sync the disks, log the
shutdown, and perform other routine shutdown and reboot activities. To shut down the system without logging the reboot, enter: reboot -l
This command shuts down the system and performs all shutdown and reboot activities, except logging the shutdown. To reboot the system
abruptly, enter: reboot -q This command reboots the system abruptly without shutting down running processes.
FILES
Specifies the command path Specifies the login accounting file Specifies the path of the syslog daemon
RELATED INFORMATION
Commands: fsck(8), halt(8), init(8), savecore(8) shutdown(8), syslogd(8)
Functions: reboot(2), sync(2), syslog(3) delim off
reboot(8)