|
|
Sponsored Content
Operating Systems
SCO
Problems installing a tape storageworks on ML350 G5 with sas hdd and 29320alp card
Post 302190384 by jactroo on Tuesday 29th of April 2008 12:59:37 PM
04-29-2008
|
|
10 More Discussions You Might Find Interesting
1. Linux
Hi,
I want to install LINUX on my laptop. I have a 2GHZ,1GB RAM and HDD is not partitioned. I donot want to touch this HDD and I have external HDD of 200GB. Can I install LINUX on this external HDD?. I would like system to detect linux only when I connect my external hard drive. else system should... (5 Replies)
Discussion started by: sureshht
5 Replies
2. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
3. SCO
Hi there
We are trying to install SCO OpenServer v5.07 on an HP ML350 G5 server.
I have downloaded the drivers from HP's website, but are getting nowhere. (I feel that I am going round in circles - every time I google for the drivers, I end up here.) :(
What happens is we create the driver... (12 Replies)
Discussion started by: The_Librarian
12 Replies
4. Solaris
I am looking for this document UNIX Configuration Guide on the HP StorageWorks Tape.
I need a procedure to install StorageWorks DAT 40 internal tape drive C5668A. (10 Replies)
Discussion started by: real-chess
10 Replies
5. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
6. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
7. Solaris
i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10.
Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6.
while reading through the user guide i got pretty confuse.
... (1 Reply)
Discussion started by: monstar1407
1 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. OS X (Apple)
Hi,
As I did not find any specific group for this question, i am putting it here.
Can I install Mac OS on an external hard disk?
Is this possible or not? I know it is very hard to install mac os on non-mac hardwares. I have a dell inspiron laptop and i want to use mac from external hdd.
... (1 Reply)
Discussion started by: sanzee
1 Replies
10. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
LEARN ABOUT REDHAT
tapeinfo
TAPEINFO(1) General Commands Manual TAPEINFO(1) NAME
tapeinfo - report SCSI tape device info SYNOPSIS
tapeinfo -f <scsi-generic-device> DESCRIPTION
The tapeinfo command reads various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It issues raw commands directly to the tape drive, using either the operating system's SCSI generic device ( e.g. /dev/sg0 on Linux, /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems. One good time to use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API, 'tapeinfo' will report a more exact description of what went wrong. Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information. OPTIONS
The first argument, given following -f , is the SCSI generic device corresponding to your tape drive. Consult your operating system's doc- umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0). Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls them. Under Linux, "cat /proc/scsi/scsi" will tell you what SCSI devices you have. BUGS AND LIMITATIONS
This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT). AVAILABILITY
tapeinfo is currently being maintained by Eric Lee Green <eric@badtux.org> formerly of Enhanced Software Technologies Inc. The 'mtx' home page is http://mtx.sourceforge.net and the actual code is currently available there and via CVS from http://sourceforge.net/projects/mtx/ . SEE ALSO
mt(1),mtx(1),scsitape(1) TAPEINFO1.0 TAPEINFO(1)