Connecting SGI to Linksys router Post: 302189574

10 More Discussions You Might Find Interesting

1. IP Networking

Connecting SGI to Windows PC

I am trying to network an SGI running Irix 6.5 through an ethernet line to a PC running Windows 2000 (I have connected other PC's to this PC without any problems.) The PC has a DSL connection from Verizon that does not support Unix. I tried using DHCP on the SGI, but when I open a web browser on...

2. IP Networking

cannot ping router from sgi irix

anyone available to help me config sgi octane to netscape and networking mac os X? i have three macs and one sgi. setup on a dsl netopia router. all 4 computers can ping each other by addresses and by names. all the macs can ping the router, but the sgi cannot ping the router, "network is...

3. Solaris

I can't ping my linksys router from Ultra 10

To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still...

4. IP Networking

router Linksys

I have a linksys router BEFSR41. I am trying to connect two network.. one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95. In the configuration LAN ip address by default it 192.168.1.1 If I define LAN IP to...

5. IP Networking

linksys router and solaris 8

I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I...

6. Shell Programming and Scripting

using wget to submit a form on linksys router

I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below). http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127 Here is my wget command: wget --http-user=xyz --http-password=xyz...

7. IP Networking

Linksys RV802 VPN Router

Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more. ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100

8. Cybersecurity

Linksys router question

Hi I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop. Yes. I did enable encryption to connect. Also my wireless printer is connected to that. For some reason, last night around 12:30 AM, the...

9. UNIX for Dummies Questions & Answers

[Solved] Can't get on internet with Linux Static IP address and Linksys Router.

I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet. When I switch back to "Automatically obtain IP address" ..then I can get on the internet. Can comeone help with this.

10. Hardware

SUN V245 Connecting To router Through Alom

Hello. I have a sun v245 and I have no hard drive for it yet but i would like to connect it to my home router by ethernet cable so I can use Alom remotely. Could someone please tell me how to set it up. Thank You

LEARN ABOUT DEBIAN

pbuilder-uml.conf

pbuilder-uml.conf(5)						     pbuilder						      pbuilder-uml.conf(5)

NAME

       pbuilder-uml.conf - configuration file for user-mode-linux port of pbuilder

DESCRIPTION

       /etc/pbuilder/pbuilder-uml.conf contains default values used in pbuilder-user-mode-linux program invocation.

FORMAT

       MY_ETH0=tuntap,,,192.168.0.2
	      Configures ethernet setting used for booting linux.  See how rootstrap boots your system, and copy that.

	      Specify --eth0=slirp,12345,/usr/bin/slirp-fullbolt to use the slirp connection.

       UML_IP=192.168.0.3
	      IP address to use for guest OS.

	      This can be set to dhcp for obtaining IP address through DHCP.

       UML_NETMASK=255.255.255.0
	      Guest OS netmask

       UML_NETWORK=192.168.0.0
	      Guest OS network

       UML_BROADCAST=255.255.255.255
	      Guest OS broadcast

       UML_GATEWAY=192.168.0.1
	      Guest OS gateway

       PBUILDER_UML_IMAGE=${HOME}/uml-image
	      Guest OS file system image.

       UML_MOUNT_TMPFS=no
	      Whether to mount tmpfs inside the guest image.  This is probably mostly useless.

       BUILDPLACE=${HOME}/tmp/
	      The  location  which build will take place.  pbuilder-user-mode-linux will place temporary COW files to there.  The user running UML
	      needs to be able to access that directory.

       UML_MEM=128
	      The amount of memory allowed for UML.  Give more value to here.

       UML_HOSTNAME=uml-host
	      The hostname for the UML.

	      The hostname should be available in /etc/hosts so that hostname -f will be able to return the FQDN.

       UML_BUILDRESULT=/directory/of/build/result
	      The directory where build result of pbuilder-user-mode-linux is stored.

       ROOTSTRAP_IMAGESIZE=size-in-megabytes
	      The size, in MB, of the disk iamge to create. Defaults to 1000.

NOTES

       It is advised to set APTCACHEHARDLINK to no in ~/.pbuilderrc.  see pbuilderrc(5) for details.

AUTHOR

       Initial coding, and main maintenance is done by Junichi Uekawa <dancer@debian.org>.

       The homepage is available at http://pbuilder.alioth.debian.org

FILES

       /etc/pbuilder/pbuilder-uml.conf, ${HOME}/.pbuilderrc

SEE ALSO

       /usr/share/doc/pbuilder/pbuilder-doc.html, pbuilder-user-mode-linux(1), pbuilder(8), pbuilderrc(5), pdebuild(1)

Debian								    2003 Jan 8						      pbuilder-uml.conf(5)

10 More Discussions You Might Find Interesting

1. IP Networking

Connecting SGI to Windows PC

Discussion started by: mdbanas

2. IP Networking

cannot ping router from sgi irix

Discussion started by: eidde

3. Solaris

I can't ping my linksys router from Ultra 10

Discussion started by: cstovall

4. IP Networking

router Linksys

Discussion started by: ajnabi