04-26-2008
What are you trying to configure? IPAT via IP Aliasing or IPAT via IP Replacement?
Aliasing: the cluster interfaces must be on different subnets and the service IP must not be in a subnet used by a non-service adapter.
Replacement: the service IP must be in the same subnet as the non-service adapter subnet.
Read the HACMP installation guide that is available from the IBM website for free. Additionally you could have a look at the redbook sg24-6769-00 (HACMP Cookbook)
10 More Discussions You Might Find Interesting
1. AIX
(0 Replies)
Discussion started by: mhenryj
0 Replies
2. AIX
Hello
I am a noobie to HACMP
I have 2 55A servers and a 7031 disk subsystem
For HACMP to work, do I need to have the hdisks on both servers to match the same drives??
The hdisks on each box are currently different:
hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies
3. AIX
Hello folks,
I am facing a problem with NFS after doing the HACMP configuration
Issue : The showmount -e pr2serv at pr1serv ,it is only showing 1 mount exported /oracle , instead of showing all 7 as per /etc/exports file.
issue : while mounting /oracle at pr1serv getting permission... (8 Replies)
Discussion started by: filosophizer
8 Replies
4. AIX
Hi,
Can we use network for heartbeat, I mean can we use different network card for heartbeat. (6 Replies)
Discussion started by: vjm
6 Replies
5. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
6. AIX
Hi,
I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide:
kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02.
I'm using nfs4 with filesystem for nfs is: /sapnfs
Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies
7. AIX
There is a shared volume group connected to two AIX systems A and B on a shared storage. The shared volume group was regularly attached to the system A and in case of a system A crash, the system B should take over the shared volume group and resources on it. Resources on the shared storage:... (1 Reply)
Discussion started by: yamanu
1 Replies
8. AIX
Does anyone has idea about, what is the ibm standard HACMP trip interval?
We have 20 second.
lssrc -ls topsvcs
Subsystem Group PID Status
topsvcs topsvcs 1843200 active
Network Name Indx Defd Mbrs St Adapter ID Group ID
HB Interval =... (7 Replies)
Discussion started by: allwin
7 Replies
9. AIX
Hi.
We have a two node HA cluster.
We got a request to change one of the VG name?
Is there an option to do this online ? If it requires downtime can someone please explain me the steps for doing it ?
Let me know if you need any outputs from the servers (1 Reply)
Discussion started by: newtoaixos
1 Replies
10. AIX
hello
ive 2 nodes aix 6100-04-10-1119 with hacmp 6.1.0.0
my qustion is :
can i add default gateway to one member node with hacmp a live or to do take over to realse one of the members ?
thanks
When it is urgent, then open the thread up in the appropriate subforum next time, thanks. (3 Replies)
Discussion started by: ariec
3 Replies
LEARN ABOUT DEBIAN
net::subnets
Net::Subnets(3pm) User Contributed Perl Documentation Net::Subnets(3pm)
NAME
Net::Subnets - Computing Subnets In Large Scale Networks
SYNOPSIS
use Net::Subnets;
my $sn = Net::Subnets->new;
$sn->subnets(@subnets);
if (my $subnetref = $sn->check($address)) {
...
}
my ($lowipref, highipref) = $sn->range($subnet);
my $listref = $sn->list(($lowipref, $highipref));
DESCRIPTION
Very fast matches large lists of IP addresses against many CIDR subnets and calculates IP address ranges.
This is a simple and efficient example for subnet matching:
use Net::Subnets;
my @subnets = qw(10.0.0.0/24 10.0.1.0/24);
my @addresses = qw/10.0.0.1 10.0.1.2 10.0.3.1/;
my $sn = Net::Subnets->new;
$sn->subnets(@subnets);
my $results;
foreach my $address (@addresses) {
if (my $subnetref = $sn->check($address)) {
$results .= "$address: $$subnetref
";
}
else {
$results .= "$address: not found
";
}
}
print($results);
This is a simple example for range calculation:
use Net::Subnets;
my @subnets = qw(10.0.0.0/24 10.0.1.0/24);
my $sn = Net::Subnets->new;
my $results;
foreach my $subnet (@subnets) {
my ($lowipref, $highipref) = $sn->range($subnet);
$results .= "$subnet: $$lowipref - $$highipref
";
}
print( $results );
This is a simple example for list generation:
use Net::Subnets;
my $lowip = '192.168.0.1';
my $highip = '192.168.0.100';
my $sn = Net::Subnets->new;
my $listref = $sn->list(($lowip, $highip));
foreach my $address (@$listref) {
# do something cool
}
METHODS
"new"
my $subnets = Net::Subnets->new;
Creates an "Net::Subnets" object.
"subnets"
$subnets->subnets([qw(10.0.0.0/24 10.0.1.0/24)]);
The C<subnets> method lets you prepare a list of CIDR subnets.
"check"
my $match = $subnets->check($address);
The C<check> method lets you check an IP address against the previously
prepared subnets.
"range"
my ($lowest, $highest) = $subnets->range($subnet)
The C<range> method lets you calculate the IP address range of a subnet.
"list"
my $list = $subnets->list($lowest, $highest);
The C<list> method lets you calculate a list containing all IP addresses
in a given range.
AUTHOR
Sebastian Riedel (sri@cpan.org), Juergen Peters (juergen.peters@taulmarill.de)
COPYRIGHT AND LICENSE
Copyright (C) 2003-2009, Sebastian Riedel.
This program is free software, you can redistribute it and/or modify it under the terms of the Artistic License version 2.0.
perl v5.10.1 2009-12-18 Net::Subnets(3pm)