04-22-2008
vendor info. link speed. ..etc..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
VALE(4) BSD Kernel Interfaces Manual VALE(4)
NAME
vale -- a very fast Virtual Local Ethernet using the netmap API
SYNOPSIS
device netmap
DESCRIPTION
vale is a feature of the netmap(4) module that implements multiple Virtual switches that can be used to interconnect netmap clients, includ-
ing traffic sources and sinks, packet forwarders, userspace firewalls, and so on.
vale is implemented completely in software, and is extremely fast. On a modern machine it can move almost 20 Million packets per second
(Mpps) per core with small frames, and about 70 Gbit/s with 1500 byte frames.
OPERATION
vale dynamically creates switches and ports as clients connect to it using the netmap(4) API.
vale ports are named vale[bdg:][port] where vale is the prefix indicating a VALE switch rather than a standard interface, bdg indicates a
specific switch (the colon is a separator), and port indicates a port within the switch. Bridge and port names are arbitrary strings, the
only constraint being that the full name must fit within 16 characters.
See netmap(4) for details on the API.
LIMITS
vale currently supports up to 4 switches, 16 ports per switch, with 1024 buffers per port. These hard limits will be changed to sysctl vari-
ables in future releases.
SYSCTL VARIABLES
vale uses the following sysctl variables to control operation:
dev.netmap.bridge The maximum number of packets processed internally in each iteration. Defaults to 1024, use lower values to trade
latency with throughput.
dev.netmap.verbose Set to non-zero values to enable in-kernel diagnostics.
EXAMPLES
Create one switch, with a traffic generator connected to one port, and a netmap-enabled tcpdump instance on another port:
tcpdump -ni vale-a:1 &
pkt-gen -i vale-a:0 -f tx &
Create two switches, each connected to two qemu machines on different ports.
qemu -net nic -net netmap,ifname=vale-1:a ... &
qemu -net nic -net netmap,ifname=vale-1:b ... &
qemu -net nic -net netmap,ifname=vale-2:c ... &
qemu -net nic -net netmap,ifname=vale-2:d ... &
SEE ALSO
netmap(4)
http://info.iet.unipi.it/~luigi/vale/
Luigi Rizzo, Giuseppe Lettieri: VALE, a switched ethernet for virtual machines, June 2012, http://info.iet.unipi.it/~luigi/vale/
AUTHORS
The vale switch was designed and implemented in 2012 by Luigi Rizzo and Giuseppe Lettieri at the Universita` di Pisa.
vale was funded by the European Commission within FP7 Projects CHANGE (257422) and OPENLAB (287581).
BSD
July 27, 2012 BSD