04-22-2008
what do you get if you force a ping out bge3 to the default gwy? can you ping that gwy?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies
3. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
4. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
macping
MACPING(1) General Commands Manual MACPING(1)
NAME
macping - A tool for pinging other RouterOS or mactelnetd devices
SYNOPSIS
mactelnet [options] <MAC-Address|hostname>
DESCRIPTION
This tool enables you to ping other RouterOS or MAC-Telnetd enabled devices. You can ping either a hostname or a MAC address. If speci-
fied, the hostname (identity) will be looked up via MNDP discovery.
OPTIONS
These programs follow the usual GNU command line syntax. A summary of options is included below.
-f Fast mode, do not wait before sending next ping request. The next ping will be sent immediately when the last ping is received. This
cannot be used with -c 0
-s Specify the amount of bytes to send in each ping packet, up to ~1400 bytes.
-c Number of packets to send before exiting. A value of 0 means unlimited packets and the tool must be exited with Control + C.
-h Show summary of options.
-v Show version of program.
SEE ALSO
mndp(1), mactelnet(1), mactelnetd(1).
AUTHOR
macping was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>.
This manual page was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>, for the Debian project (and may be used by others).
February 27, 2011 MACPING(1)