04-18-2008
Is this applicable to Solaris 8?.
Sorry for the cross post.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Sorry if this is not the right folder...
I come across these terms..
-Disk Array
-Clustering
What are they? When and how will we use them?
Please teach me.
Thanks (1 Reply)
Discussion started by: champion
1 Replies
2. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
3. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
4. UNIX for Advanced & Expert Users
I have a 3510 disk array attached to a T2000 server.
The dmesg command shows disk error as follows and is generated a couple of times during the day
Aug 18 03:35:51 myserver SUNWscsdMonitor: <rctrl6042> Standard General Event, CHL:2 ID:22 Drive NOTICE: Drive Recovered Error - 5F8E1F... (1 Reply)
Discussion started by: Tirmazi
1 Replies
5. Solaris
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Discussion started by: jamie_collins
4 Replies
6. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
7. Solaris
So I have 2 solaris sun servers one with a disk array with 14 drives which I need to move to the other server. How do I move the disk array configured as a Raid 5 to another server without losing data? So far I know I'll connect the drive, run devfsadm, use format to verify the server see's... (5 Replies)
Discussion started by: Kjons76
5 Replies
8. UNIX for Advanced & Expert Users
HI:
I have a DUAL redundant system running in HP-UX 10.20 ( 2 servers)
Both servers share an external SCSI disk array. Both server runs a Data base wich uses the disk array to write the data, and that is the way they share the information.
The way that the servers see the disk array, is like... (1 Reply)
Discussion started by: pmoren
1 Replies
9. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
10. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
LEARN ABOUT DEBIAN
blaze-remove
BLAZE-REMOVE(1) BlazeBlogger Documentation BLAZE-REMOVE(1)
NAME
blaze-remove - removes a post or page from the BlazeBlogger repository
SYNOPSIS
blaze-remove [-fipqPV] [-b directory] id...
blaze-remove -h|-v
DESCRIPTION
blaze-remove removes a blog post or a page with the specified id from the BlazeBlogger repository.
OPTIONS
-b directory, --blogdir directory
Allows you to specify a directory in which the BlazeBlogger repository is placed. The default option is a current working directory.
-p, --page, --pages
Tells blaze-remove to remove a page or pages.
-P, --post, --posts
Tells blaze-remove to remove a blog post or blog posts. This is the default option.
-f, --force
Disables requiring manual confirmation of each blog post or page removal. This is the default option.
-i, --interactive
Enables requiring manual confirmation of each blog post or page removal.
-q, --quiet
Disables displaying of unnecessary messages.
-V, --verbose
Enables displaying of all messages. This is the default option.
-h, --help
Displays usage information and exits.
-v, --version
Displays version information and exits.
EXAMPLE USAGE
Remove a blog post:
~]$ blaze-remove 10
Successfully removed the post with ID 10.
Remove a page:
~]$ blaze-remove -p 4
Successfully removed the page with ID 4.
Remove multiple blog posts:
~]$ blaze-remove 10 4 6
Successfully removed the post with ID 10, 4 and 6.
Remove multiple blog posts safely:
~]$ blaze-remove -i 10 4 6
Remove the post with ID 10 titled `Debian and Fedora Packages'? y
Remove the post with ID 4 titled `BlazeBlogger 0.8.0 RC2'? y
Remove the post with ID 6 titled `BlazeBlogger 0.8.1'? y
Successfully removed the post with ID 10, 4 and 6.
SEE ALSO
blaze-config(1), blaze-add(1), blaze-list(1)
BUGS
To report a bug or to send a patch, please, add a new issue to the bug tracker at <http://code.google.com/p/blazeblogger/issues/>, or visit
the discussion group at <http://groups.google.com/group/blazeblogger/>.
COPYRIGHT
Copyright (C) 2008-2011 Jaromir Hradilek
This program is free software; see the source for copying conditions. It is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Version 1.2.0 2012-03-05 BLAZE-REMOVE(1)