04-16-2008
thanks
thank you men but the first code
sum=0
for s in $seira; do
sum=`expr $sum + $s`
done
this is in the while loop or it is appart. When will it end?
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
sry im new to this...another qns..
if i have a line in the normal shell the file is email.scp. it contains a txt file eg hello.txt that contain this infomation.
k@hotmail.com
j@jotm.com
how do i delete away the blank spaces after the k@hotmail.com..i dun wan any blank spaces after the... (2 Replies)
Discussion started by: forevercalz
2 Replies
2. Shell Programming and Scripting
can any help how to remove blank spaces in a string?
STR="GOOD BYE"
by removing blank spaces, the string should be GOOD,BYE
thanks in advance (2 Replies)
Discussion started by: spandu
2 Replies
3. Shell Programming and Scripting
I have to filter out data from a file based on the value of first three characters of each record I have used the following logic
FIN=$LOC/TEST2.TXT
FEEDFILE=$LOC/TEST1.TXT
while read FDROW
do
FEEDROW=$FDROW;
DTYPE=`echo $FEEDROW |cut -c 1-3`
if ; then
echo $FEEDROW >> $FIN... (5 Replies)
Discussion started by: gander_ss
5 Replies
4. Shell Programming and Scripting
Hello All,
I am trying to remove all tabspaces and all blankspaces from my file using sed & awk, but not getting proper code. Please help me out.
My file is like this (<b> means one blank space, <t> means one tab space)-
$ cat file
NARESH<b><b><b>KUMAR<t><t>PRADHAN... (3 Replies)
Discussion started by: NARESH1302
3 Replies
5. UNIX for Dummies Questions & Answers
Hi,
I'm a newbie to shell scripting and I have the following problem:
I need all spaces between two letters or a letter and a number exchanged for an underscore, but all spaces between a letter and other characters need to remain. Searching forums didn't help...
One example for clarity:
... (3 Replies)
Discussion started by: Cpt_Cell
3 Replies
6. Shell Programming and Scripting
Hello, could you please help with this one. I have an input file like this:
123,4567,89000
123456789,9876543,12
and for the output I need strings to be with the fixed length, let's say 15, and if the string is -lt 15 to be populated with blanks at the end until it reach 15, like this:
123 ,4567... (1 Reply)
Discussion started by: apenkov
1 Replies
7. Shell Programming and Scripting
Gents,
Please can you help me.. to remove blank spaces :)
Input
ABSOLUTE , ,FALSE ,1035 ,28 ,669 ,1817.0 ,CORREL BEFORE ,1
ABSOLUTE , ,FALSE ,1035 ,28 ,686 ,1817.0 ,CORREL BEFORE ,1
ABSOLUTE , ,FALSE ,1035 ,28 ,670 ,1819.0 ,CORREL BEFORE ,1
ABSOLUTE , ,FALSE ... (4 Replies)
Discussion started by: jiam912
4 Replies
8. UNIX for Dummies Questions & Answers
Dear Masters,
I want to remove all lines with blank spaces
input file:
a|abc|0|1
a|abc|2|3
b||3|5
c|def||7
d|def|0|1
Expected:
a|abc|0|1
a|abc|2|3
d|def|0|1
I did this
awk -F'|' '!/^$/' input (4 Replies)
Discussion started by: radius
4 Replies
9. UNIX for Advanced & Expert Users
Hi Gurus,
Somebody can say me how to delete blank spaces and blank lines in a file unix, please.
Thank you for advanced. (10 Replies)
Discussion started by: systemoper
10 Replies
10. Shell Programming and Scripting
Hi Guru,
I need some advice on how to add blank spaces to the code, rather than me just adding <space-bar spaces> which does not work.
Current output of the code
File System Backed Up - ALL_LOCAL_DRIVES
Daily - Incremental Backup Schedule - 1 Month Retention
• 7pm - PRD... (2 Replies)
Discussion started by: Junes
2 Replies
sum(1) General Commands Manual sum(1)
NAME
sum - Displays the checksum and byte count in block-size (1024) units of a file
SYNOPSIS
sum [-o | -r] [file...]
The sum command reads file and calculates a 16-bit checksum and the byte count in block-size (1024) units in the file. If the file argu-
ment is omitted, sum reads standard input.
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
sum: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
OPTIONS
[Tru64 UNIX] Uses an algorithm to compute the checksum using word-by-word computation. Uses an alternate algorithm to compute the check-
sum (rigorous byte-by-byte computation rather than the word-by-word computation).
[Tru64 UNIX] This is the default.
OPERANDS
The file for which a checksum is to be computed. If this operand is omitted, standard input is used.
DESCRIPTION
The checksum and number of blocks are written to standard output. The sum command is generally used to determine if a file that was copied
or communicated over transmission lines is an exact copy of the original. The sum command writes the space used in 1024-byte units.
[Tru64 UNIX] The checksum is calculated using a rigorous byte-byte computation by default.
System V Compatibility
[Tru64 UNIX] The checksum algorithms for the default sum command and the SVID 2 compliant sum command are reversed. The SVID 2 compliant
sum command uses the word-by-word algorithm by default and uses the byte-by-byte algorithm if you specify the -r option on the command
line.
NOTES
The sum utility is marked LEGACY in XCU Issue 5. [Tru64 UNIX] The default algorithm is no longer the word-by-word computation algorithm.
It was changed to the 4.3BSD default algorithm. The algorithms used may not be portable, that is, the same checksum may not be produced
for the same input on different systems. Portable applications should use cksum.
EXIT STATUS
The following exit values are returned: Successful completion. An error occurred.
EXAMPLES
To display the checksum of datafile and the number of blocks in this file, enter: sum datafile
If the checksum of datafile is 1605 and if the file contains 3 blocks, sum displays: 1605 3 datafile
ENVIRONMENT VARIABLES
The following environment variables affect the execution of sum: Provides a default value for the internationalization variables that are
unset or null. If LANG is unset or null, the corresponding value from the default locale is used. If any of the internationalization vari-
ables contain an invalid setting, the utility behaves as if none of the variables had been defined. If set to a non-empty string value,
overrides the values of all the other internationalization variables. Determines the locale for the interpretation of sequences of bytes
of text data as characters (for example, single-byte as opposed to multibyte characters in arguments). Determines the locale for the for-
mat and contents of diagnostic messages written to standard error. Determines the location of message catalogues for the processing of
LC_MESSAGES.
SEE ALSO
Commands: cksum(1), wc(1)
Standards: standards(5)
sum(1)