04-15-2008
thankq..,
it is very help full to me...,
as well as if i wanna take a SVM disk back to OS.
1) i need to detach the mirroring volumes,
2) metaclear the all volumes
3) delete the all replicas on tht disk.
then we can say the disk is under OS control.
is this correct. or did i missed anything..,
thanks once again
Last edited by b.janardhanguru; 03-11-2009 at 10:22 PM..
9 More Discussions You Might Find Interesting
1. Solaris
Hi all,
I have a problem with vxvm volume which is mirror with two disks. when i am try to increase file system, it is throwing an ERROR: can not allocate 5083938 blocks, ERROR: can not able to run vxassist on this volume.
Please find a sutable solutions.
Thanks and Regards
B. Nageswar... (0 Replies)
Discussion started by: nageswarb
0 Replies
2. Solaris
Hello experts..
How can i grow Raid 5 volume in SVM?
Thanks in advance.. (2 Replies)
Discussion started by: younus_syed
2 Replies
3. Solaris
pupp, thanks for the information. but is its integrated volume management better than SVM that we use (with ufs i believe)? (2 Replies)
Discussion started by: StarSol
2 Replies
4. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
5. Solaris
How to check Solaris Volume Manager Version in 9 & 10? Which are the packages that are installed in the SVM? (1 Reply)
Discussion started by: ajhal04
1 Replies
6. Shell Programming and Scripting
OS version : AIX 6.1
Shell : Korn
When you 'postfix' a command with ampersand (&) , it is supposed to run in the background and give you back the control.
I tested this with ping command (by default it pings every 1 second )
After I ran the below ping command with ampersand, I pressed... (3 Replies)
Discussion started by: polavan
3 Replies
7. Solaris
Hi All
I want to extend this file system to 120Gb:
df -h /xyz
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d80 98G 35G 62G 37% /xyzand the NetApp admin is going to give me an LUN with 22Gb.
This file system is mounted on:
metastat d80... (1 Reply)
Discussion started by: fretagi
1 Replies
8. Solaris
Hello Gurus,
I am setting up a V240 with solaris 10 for learning purpose. I have 4 x 36Gb disk installed and I now want to install SVM just tp learn this disk management utility. What I want to know is where do I look for the SVM pkg ?
is this the right command pkgchk -L SUNWsvm . Can anyone... (3 Replies)
Discussion started by: Moh
3 Replies
9. Shell Programming and Scripting
Hi All,
I have a shell script(test_abc.sh) with the following shell commands, which are invoking the same shell script with different parameters.
test_abc.sh
. ./test.sh abc >> test.log
. ./test.sh xyz >> test.log
. ./test.sh pys >> test.log
. ./test.sh abc >> test.log
.
.
... (4 Replies)
Discussion started by: dev.devil.1983
4 Replies
LEARN ABOUT HPUX
vxvmboot
vxvmboot(1M) vxvmboot(1M)
NAME
vxvmboot - prepare Veritas Volume Manager volume as a root, boot, primary swap or dump volume
SYNOPSIS
/sbin/vxvmboot [-b|-d|-r|-s] [-v] -o offset -l length rawpath
/sbin/vxvmboot -v rawpath
/sbin/vxvmboot -c
DESCRIPTION
The vxvmboot command updates information in the LABEL file for the lif disk specified by the pathname of its character (raw) device node,
rawpath. The volume at the specified offset and length becomes the boot, root, primary swap or dump volume when the system is next booted.
This command is normally invoked by the vxbootsetup utility.
OPTIONS
-b Specifies the volume type as a boot volume with name standvol.
-c Is used to update the /stand/rootconf file with the offset and length of the rootvol. The usage is slightly different when the -c
argument is used. The rawpath argument is not used with this invocation. Instead the path of the boot device is extracted from
the /stand/bootconf file. Also, the -o and -l arguments are not used to specify the offset and length. Instead, the offset and
length of the rootvol are obtained from the LIF LABEL file on the boot device.
The -c option would normally be used in the sbin/ioinitrc script to update the /stand/rootconf file, when the boot disk is VxVM
rootable.
-d Specifies the volume type as a dump volume with name dumpvol.
If a dumpvol volume exists on the specified disk, the extent information from this volume is used. If no such volume exists, the
extent information of the swap volume is used instead, and swapvol performs the dual role of swap device and dump device.
-l length Specifies the length of the volume in units of 1024-byte blocks.
-o offset Specifies the start of the volume as the number of 1024-byte blocks from the beginning of the disk.
-r Specifies the volume type as a root volume with name rootvol.
-s Specifies the volume type as a swap volume with name swapvol.
-v When used with one of the options -b, -d, -r or -s, displays the contents of the updated LABEL file. Otherwise, this option may
be used to display the contents of the LABEL file on the specified lif disk.
Note: The -b, -c, -d, -r and -s options are mutually exclusive. If more than one of these options is specified, the vxvmboot com-
mand exits without performing any operation.
ARGUMENTS
rawpath Specifies the pathname of the character (raw) device node for the lif disk.
SEE ALSO
lif(4), mkboot(1M), vxbootsetup(1M)
VxVM 5.0.31.1 24 Mar 2008 vxvmboot(1M)