04-07-2008
I have disabled nwam..
However i would like to know how to use nwam?
coming to the main picture...
i can ping only my host ip..
anyother ip or anyother dns is not working!!!
But i can assure you that my network interface is being detected...
$network-admin
when the window opens up, my interface is shown as active and its nge0.
it also shows up on ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
nge0: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 2
inet 0.0.0.0 netmask ff000000 broadcast 0.255.255.255
ether 96:bd:ea:fc:1b:0
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
inet6 ::1/128
can you tell me what am doing wrong???
btw am using a on-board ethernet card from nvidia!!!
My winxp gets the ip automatically....
So i thought of setting up DHCP on solaris, when that didnt work i tried a static ip format but that didnt go as planned either
Last edited by wrapster; 04-07-2008 at 01:38 PM..
Reason: missed out
10 More Discussions You Might Find Interesting
1. IP Networking
I am moving a SUN 250 server from one location to another. The IP address has to change in order to make the server visible in the new building. The system administrator has given me the new IP address for the server, the DNS server IP and the default gateway IP. First question, is this all the... (2 Replies)
Discussion started by: pkappaz
2 Replies
2. Solaris
on sparc solairs 2.8 which files i need to configure for network setup:
/etc/hosts
/etc/defaultrouter
/etc/netmasks
/et/resolv.conf
what els?.
by the way, how do i configure for rsh?.
like for doing "rsh remotehostname date"?. (2 Replies)
Discussion started by: S26+
2 Replies
3. IP Networking
Hello everybody,
I am a new unix user (Solaris 10). I was wondering if anybody can help me figure out how to connect to the network in my work place. I know my IP address, subnet mask, gateway, primary and secondary DNS addresses but I don't know how to enter these settings into my Solaris.
... (3 Replies)
Discussion started by: arash05
3 Replies
4. Solaris
Please help urgently.
I need to setup up some sort of service on a solaris server on a port.
I dont need it do anything special, anything that is sent to this port from an external server should be dump to /dev/null or a flat file..
Can you help urgently? (1 Reply)
Discussion started by: frustrated1
1 Replies
5. Solaris
hi experts,
very need help, i had setup the SSH on solaris 8 and have generate the key but i have problem to start the sshd below is the error messages :
/etc/rc2.d/S97sshd start
Could not load host key: /usr/local/etc/ssh_host_key
Could not load host key: /usr/local/etc/ssh_host_rsa_key... (6 Replies)
Discussion started by: bucci
6 Replies
6. Shell Programming and Scripting
Hi all,
I was playing around with some scripts and spoilt solaris completely ..
So i reinstalled and thought of giving the password once i log in...
However i forgot all about it and went ahead installing all my drivers and particularly KDE 3.5.8 on my system..
But for kde to show up at the... (0 Replies)
Discussion started by: wrapster
0 Replies
7. Solaris
hi,
i have sunfire 280r sparc. i would like to know how to setup interface with command ndd line and put it in the file permanently.
my card is eri0 and speed can be 100mb or 1000mb full duplex.
thanks in advance. (3 Replies)
Discussion started by: lamoul
3 Replies
8. Shell Programming and Scripting
Hi Gurus,
We need to make SFTP in non_interactive mode. I have done steps like key generation, copying public key into destination server, changing file/folder permission. Still we are not able to achieve it. Please check the log below....
$ sftp -v b2cint@10.76.120.120
Connecting to... (1 Reply)
Discussion started by: Sabari Nath S
1 Replies
9. IP Networking
Can someone here please help and walk me through what I need to do to setup
my network so that I can start an oracle listener ?
I am connected through a router (netgear) and everytime I start my machine the ip address changes because of DHCP (I think). There are so many parameters that I do... (5 Replies)
Discussion started by: jxh461
5 Replies
10. Linux
I attempted to update Python on my CentOS 5.6 VM and have encountered some issues after then. Initially yum wouldn't work, but I have resolved that.
However, now I am unable to access the Network Configuration section under setup.
When I do select this option I see this at the command line:
... (2 Replies)
Discussion started by: crmpicco
2 Replies
LEARN ABOUT X11R4
systemd-networkd
SYSTEMD-NETWORKD.SERVICE(8) systemd-networkd.service SYSTEMD-NETWORKD.SERVICE(8)
NAME
systemd-networkd.service, systemd-networkd - Network manager
SYNOPSIS
systemd-networkd.service
/lib/systemd/systemd-networkd
DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating
virtual network devices.
To configure low-level link settings independently of networks, see systemd.link(5).
systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in
those files.
systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match]
section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any
links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by
using Unmanaged=yes option, see systemd.network(5).
When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition
from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and
systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up
manually.
CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network
directory /run/systemd/network and the local administration network directory /etc/systemd/network.
Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see
systemd.netdev(5).
SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8)
systemd 237 SYSTEMD-NETWORKD.SERVICE(8)