04-02-2008
Not working
Hi
if I do
grep -v "Permission denied" today.txt
It is printing the text without the line on the screen
but it si not deleting the line in the file.
So how can I do that, like delete the line from the file itself as i am mailing the file after i do this operation.
Regards,
gns
PS: Sorry for multiple posting
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi I have a text file like this name today.txt
the request has been accepted
the scan is successful at following time
there are no invalid packages
5169378 : map : Permission Denied
the request has been accepted
Now what i want do is
I want to search the today.txt file and
if i... (1 Reply)
Discussion started by: gsusarla
1 Replies
2. Shell Programming and Scripting
I am searching a dhcpd.conf to find the hardware ethernet match, then once the match is found delete just the line above it. For example:
testmachine.example {
hardware ethernet 00:00:00:00:00:00;
fixed address 192.168.1.100;
next-server 192.168.1.101;
filename "linux-install/pxelinux.0";
}... (3 Replies)
Discussion started by: cstovall
3 Replies
3. Shell Programming and Scripting
Hi All,
I would like to fine some entry in a file, if it found, it should remove the same in the same file.
Please some one help me.
need to find and en entry 'bea' from hosts file. If it found it should write it same host file.
but i am not geting it. If i am writing it in new file... (2 Replies)
Discussion started by: bullz26
2 Replies
4. UNIX for Dummies Questions & Answers
I am trying to delete the line with pattern and the next line. Found the below command in forum which also deleted the previous line. how should i modify that to make sure that only the line with pattern and the next line are deleted but not the previous line?
awk '/key... (1 Reply)
Discussion started by: rdhanek
1 Replies
5. Shell Programming and Scripting
i need to find ' - ' in a line , if i found i need to rest of the line including '-'
example
libmm-2.0
libytytsunos-5.6
output
libmm
libytytsunos (7 Replies)
Discussion started by: girija
7 Replies
6. Shell Programming and Scripting
I have the following file:
line1
line2
MATCH
line3
line4
I need to find the pattern, "MATCH" and delete the line before and after MATCH. So the result should be
line1
MATCH
lline4
I have to use sed because it is the only utility that is common across my environments. I... (1 Reply)
Discussion started by: craftereric
1 Replies
7. Shell Programming and Scripting
I'm looking for a way to search a file, in this case init.rc for a specific match, service adbd /sbin/adbd, and delete the a specific line after it
Original:
# adbd is controlled by the persist.service.adb.enable system property
service adbd /sbin/adbd
disabled
After deletion:
#... (5 Replies)
Discussion started by: GabrialDestruir
5 Replies
8. UNIX for Advanced & Expert Users
Hi ,
i have a file with data as below.This is same file. But actual file contains to many rows.
i want to search for a string "Field 039 00" and delete that line and previous 3 lines in that file.. Can some body suggested me how can i do using either sed or awk command ?
Field 004... (7 Replies)
Discussion started by: vadlamudy
7 Replies
9. Shell Programming and Scripting
good day
i have a list of numbers in input.txt, i would like to compare to file.txt and delete the line that number appears in file.txt .
input.txt:
4558980
5525628
3595233
2650083
2219411
3529741
4675897
3070869
0014685
6365902
file.txt:
one-two-three-4558980.txt... (7 Replies)
Discussion started by: klein
7 Replies
10. Shell Programming and Scripting
Hello,
When my lines contain question mark, I use below command to delete the portion of the matching line coming after question mark:
sed 's/?.*//' SampleFile
SampleFile:
helloworldfirstline?mdksmyymsss
hellosecondlineworld?mdksmkkmsss
thirdhelloworld?mdksmccmsss
Output:... (2 Replies)
Discussion started by: baris35
2 Replies
trans(1int) trans(1int)
Name
trans - translation tool for use with source message catalogs
Syntax
trans [ -c ] [ -o name ] file.msf
Description
The command assists in the translation of source message catalogs. The command reads input from file.msf and writes its output to either a
file named or a file you name on the command line. The command displays file.msf in a multiple window screen that lets you simultaneously
see the original message, the translated text you enter, and any messages from the command. This multiple window screen is easier to use
for translating messages than a single window screen.
The top window in the multiple window screen displays the text in the message source file file.msf. The editor displays the current mes-
sage in reverse video.
In the center window, displays a prompt that asks you to enter a translated message. You use a control key editor to move the cursor and
delete text in the center window. The control key sequences are defined as follows:
------------------------------------------
Key Sequence Meaning
------------------------------------------
CTRL/k Display control key help
CTRL/h Back space
CTRL/l Forward space
CTRL/w Back word
CTRL/f Forward word
CTRL/e Move to end of input
CTRL/b Move to beginning of input
CTRL/n Next line
CTRL/p Previous line
CTRL/u Delete input
CTRL/i Insert mode (default)
CTRL/r Replace mode
DEL Delete previous character
------------------------------------------
If you need to span more than one line with the translated text, type a backslash () and press the RETURN key to enable line continuation.
After you finish entering the translated text, press the RETURN key to signal that you have finished translating that message.
The bottom window displays any messages generated by If an error occurs, prompts you to re-enter the entire line, including the message
label or number.
Options
-c Display comment lines beginning with a dollar sign ($) for translation, in addition to messages.
-o Call the output file name. The default is output file name is
Restrictions
Your terminal must be 80 columns by 24 lines for to display its three-window screen.
You cannot interrupt a session and restart it at the point you stopped. You must complete the all the changes to a file before exiting a
file.
See Also
intro(3int), extract(1int), gencat(1int), strextract(1int), strmerge(1int)
Guide to Developing International Software
trans(1int)