Sponsored Content
Top Forums UNIX for Advanced & Expert Users Remove /dev/sdb partition using fdisk - BY ACCIDENT! Post 302180588 by ramen_noodle on Monday 31st of March 2008 02:57:25 PM
Old 03-31-2008
Backups?

An emergency maintenance should be declared immediately to determine the damage.
Worst case: Users will not be able to commit data to disk so they are losing a days
production and all of their previous data as well.
 

10 More Discussions You Might Find Interesting

1. Solaris

recovery partition table from fdisk?

I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk. The possible reason could be: 1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies

2. Filesystems, Disks and Memory

Ran out of space on /dev/root partition

hi, I have a SCO unix server which has a 36gb hard drive, but the IT company who supplied it assigned 1gb to /dev/root, 15mb to /dev/boot and 33gb to /dev/u. The /dev/root partition is now full, is there a way I can use the 33gb assigned to /dev/u without loosing any data, preferably... (2 Replies)
Discussion started by: Martyn
2 Replies

3. UNIX for Dummies Questions & Answers

Remove /dev/sdb partition using fdisk - BY ACCIDENT!

Hello everyone - Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses. I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Discussion started by: kevindoman
2 Replies

4. UNIX for Dummies Questions & Answers

OS X fdisk - Remove bootable flag

I have a FAT32 data disk attached to my Mac. It has 1 partition that is marked as bootable and the Mac tries to boot from it even though it has no OS on it. The man page for fdisk tells how to turn on the boot flag for a partition, but not how to remove it. Is there a way? Thanks! (0 Replies)
Discussion started by: jkorchok
0 Replies

5. Filesystems, Disks and Memory

Partition management: lvm? fdisk? parted? (on RAID)

Hello, I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?). It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume. I want... (1 Reply)
Discussion started by: builder88
1 Replies

6. Shell Programming and Scripting

Non-interactive fdisk partition in script

Hi, How can I run fdisk partition in a script without interactive input? In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies

7. Red Hat

Can I change the partition type with fdisk without disrupting data?

Hello, I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies

8. Solaris

Lun remove, stuck in /dev/dsk and /dev/rdsk

So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following: devfsadm -Cv powermt -q luxadm -e offline <drive path> luxadm probe All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies

9. UNIX for Advanced & Expert Users

Disk /dev/sdb doesn't contain a valid partition table

Hello, I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output : # fdisk -l Disk /dev/sda: 107.6 GB, 107639996416 bytes 255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies

10. Red Hat

Changing grub from /dev/sda to /dev/sdb

Hi, Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 01:16 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy