03-31-2008
10 More Discussions You Might Find Interesting
1. Solaris
I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk.
The possible reason could be:
1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies
2. Filesystems, Disks and Memory
hi,
I have a SCO unix server which has a 36gb hard drive, but the IT company who supplied it assigned 1gb to /dev/root, 15mb to /dev/boot and 33gb to /dev/u.
The /dev/root partition is now full, is there a way I can use the 33gb assigned to /dev/u without loosing any data, preferably... (2 Replies)
Discussion started by: Martyn
2 Replies
3. UNIX for Advanced & Expert Users
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Discussion started by: kevindoman
5 Replies
4. UNIX for Dummies Questions & Answers
I have a FAT32 data disk attached to my Mac. It has 1 partition that is marked as bootable and the Mac tries to boot from it even though it has no OS on it. The man page for fdisk tells how to turn on the boot flag for a partition, but not how to remove it. Is there a way? Thanks! (0 Replies)
Discussion started by: jkorchok
0 Replies
5. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
6. Shell Programming and Scripting
Hi,
How can I run fdisk partition in a script without interactive input?
In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies
7. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
8. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Red Hat
Hi,
Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
LEARN ABOUT DEBIAN
bootcd2disk
BOOTCD2DISK(1) bootcd utils BOOTCD2DISK(1)
NAME
bootcd2disk - copy a system running from bootcd to a disk
SYNOPSIS
bootcd2disk [-i] [-s] [-c <config directory>] [-url <url>]
DESCRIPTION
With bootcd2disk a CD build with bootcdwrite can be copied to one or more Disk Partitions from the running cd-based system. Therefore
bootcd could be used to make rescue disks.
It is also possible to let bootcd2disk automatically find a disk, make partitions on it, copy the cd to the disk and make the disk
bootable. bootcd2disk will be available as soon as your system is running from cd.
OPTIONS
-i With this option the complete bootcd2disk runs in interactive mode and you can run each function manually. This option is useful for
debugging.
-v The option "-v" (verbose) adds messages on running.
-s This option can be used to disable interactive questions and to try to ignore errors.
-c <config directory>
The configuration directory which normally is "/etc/bootcd" can be changed with this.
-url <url>
If bootcd2disk is slow on your system (because of a slow CD/DVD drive or the HP ILO virtual CD interface), you can use an image server
to get the image from. bootcd2disk use the SWAP partition of your upcoming system as temporary space and copy the image from the con-
figured image server to this partition and use it as image. The image server url is configured with this option.
example install from imagesserver:
bootcd2disk -url http://192.168.1.1/cdimage.iso
Another way the increase the performance is the use of the mounted CD/DVD itself for the copy. The option "-url" is the same, the url
starts with "file:///"
example install from CD/DVD drive sdc0:
bootcd2disk -url file:///dev/sdc0
The swap partition of the upcoming system must have enough space to get the whole image!
Currently no other options can be specified on command line. All other configuration has to be done in the config files.
FILES
/etc/bootcd/bootcd2disk.conf
Configuration for bootcd2disk.
SEE ALSO
Documentation in bootcd2disk.conf
bootcd2disk.conf(5), bootcd(1), bootcdflopcp(1), bootcdwrite(1)
AUTHOR
This manual page was written by Bernd Schumacher <bernd.schumacher@hp.com> and Carsten Dinkelmann <Carsten.Dinkelmann@foobar-cpa.de> for
the Debian GNU/Linux system (but may be used by others).
bootcd2disk 2007-04-04 BOOTCD2DISK(1)