Sponsored Content
Top Forums UNIX for Advanced & Expert Users Remove /dev/sdb partition using fdisk - BY ACCIDENT! Post 302180582 by era on Monday 31st of March 2008 02:43:28 PM
Old 03-31-2008
It will probably be gone after the next reboot. RAID complicates matters, but I think you just might be lucky enough that it could be recovered if you can figure out what numbers to put in when you create a new partition with exactly the same parameters as the one you deleted.

There are also tools which can help you make an educated guess. TestDisk - CGSecurity is one I personally had some success with under similar circumstances.

This is Linux, right? Make a lot of sense to include platform information for this sort of question.
 

10 More Discussions You Might Find Interesting

1. Solaris

recovery partition table from fdisk?

I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk. The possible reason could be: 1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies

2. Filesystems, Disks and Memory

Ran out of space on /dev/root partition

hi, I have a SCO unix server which has a 36gb hard drive, but the IT company who supplied it assigned 1gb to /dev/root, 15mb to /dev/boot and 33gb to /dev/u. The /dev/root partition is now full, is there a way I can use the 33gb assigned to /dev/u without loosing any data, preferably... (2 Replies)
Discussion started by: Martyn
2 Replies

3. UNIX for Dummies Questions & Answers

Remove /dev/sdb partition using fdisk - BY ACCIDENT!

Hello everyone - Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses. I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Discussion started by: kevindoman
2 Replies

4. UNIX for Dummies Questions & Answers

OS X fdisk - Remove bootable flag

I have a FAT32 data disk attached to my Mac. It has 1 partition that is marked as bootable and the Mac tries to boot from it even though it has no OS on it. The man page for fdisk tells how to turn on the boot flag for a partition, but not how to remove it. Is there a way? Thanks! (0 Replies)
Discussion started by: jkorchok
0 Replies

5. Filesystems, Disks and Memory

Partition management: lvm? fdisk? parted? (on RAID)

Hello, I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?). It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume. I want... (1 Reply)
Discussion started by: builder88
1 Replies

6. Shell Programming and Scripting

Non-interactive fdisk partition in script

Hi, How can I run fdisk partition in a script without interactive input? In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies

7. Red Hat

Can I change the partition type with fdisk without disrupting data?

Hello, I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies

8. Solaris

Lun remove, stuck in /dev/dsk and /dev/rdsk

So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following: devfsadm -Cv powermt -q luxadm -e offline <drive path> luxadm probe All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies

9. UNIX for Advanced & Expert Users

Disk /dev/sdb doesn't contain a valid partition table

Hello, I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output : # fdisk -l Disk /dev/sda: 107.6 GB, 107639996416 bytes 255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies

10. Red Hat

Changing grub from /dev/sda to /dev/sdb

Hi, Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.16.3 2012-02-11 URI::URL(3)
All times are GMT -4. The time now is 01:10 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy