|
|
Sponsored Content
Top Forums
Shell Programming and Scripting
Multiple line match using sed
Post 302179083 by era on Thursday 27th of March 2008 01:19:50 AM
03-27-2008
|
|
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I need to replace the line containing "STAGE_DB" with the line
"STAGE_DB $DB # database that contains the table being loaded ($workingDB)"
Here $DB is passed during the runtime.
How can I do this?
Thanks,
Kousikan (2 Replies)
Discussion started by: kousikan
2 Replies
2. Shell Programming and Scripting
Hi all,
I've been working on a script which I have hit a road block now. I have written a script using sed to extract the below data and pumped into another file:
Severity............: MAJORWARNING
Summary:
System temperature is out of normal range.
Severity............: MAJORWARNING... (13 Replies)
Discussion started by: phixsius
13 Replies
3. Shell Programming and Scripting
Hi
I'm not very good with the serach patterns and I'd need a sample how to find a line that has multiple patterns.
Say I want to find a line that has "abd", "123" and "QWERTY" and there can be any characters or numbers between the serach patterns, I have a file that has thousands of lines and... (10 Replies)
Discussion started by: Juha
10 Replies
4. Shell Programming and Scripting
I am searching a dhcpd.conf to find the hardware ethernet match, then once the match is found delete just the line above it. For example:
testmachine.example {
hardware ethernet 00:00:00:00:00:00;
fixed address 192.168.1.100;
next-server 192.168.1.101;
filename "linux-install/pxelinux.0";
}... (3 Replies)
Discussion started by: cstovall
3 Replies
5. Shell Programming and Scripting
the following range matching works great but i wish to add a blank line after each range result set... which i've tried and researched to no avail
MY INPUT DATA:
CURRENT CODE I'M USING:
sed -n '/*$/,/;/p' $INPUT_FILE
RESULTS I'M GETTING:
RESULT I looking to... (5 Replies)
Discussion started by: danmauer
5 Replies
6. Shell Programming and Scripting
Hello,
I want to do a simple substitution using sed but I can't find a solution. Basically, from a Apache conf file, I would like to remove everything included between the <VirtualHost> and </VirtualHost> e.g
SSLMutex file:/var/run/ssl_mutex
<VirtualHost _default_:443>
# A lot of config that... (5 Replies)
Discussion started by: RobertFord
5 Replies
7. Shell Programming and Scripting
Hi,
I want to match a line which exists in a file. I have written a test script similar to below -
The content of the file file.txt would be like this -
/usr/bin/1234.xcf
/usr/bin/3456.xcf
/usr/bin/7897.xcf
/usr/bin/2345.xcf
out=`sed -n '\/usr\/bin\/7897.xcf/p' file.txt 2>&1`... (3 Replies)
Discussion started by: angshuman_ag
3 Replies
8. Shell Programming and Scripting
Dear all,
I need to search multiple patterns and then I need to print their respective next lines. For an example, in the below table, I will look for 3 different patterns :
1) # ATC_Codes:
2) # Generic_Name:
3) # Drug_Target_1_Gene_Name:
#BEGIN_DRUGCARD DB00001
# AHFS_Codes:... (3 Replies)
Discussion started by: AshwaniSharma09
3 Replies
9. Shell Programming and Scripting
Hi How Are you?
I am doing fine!
I need to go now?
I will see you tomorrow!
Basically I need to replace the entire line containing "doing" with a blank line:
I need to the following output:
Hi How Are you?
I need to go now?
I will see you tomorrow!
Thanks in advance.... (1 Reply)
Discussion started by: sags007_99
1 Replies
10. Shell Programming and Scripting
I need to match two patterns in a log file and need to get the next line of the one of the pattern (out of two patterns) that is matched,
finally need to print these three values in a single line.
Sample Log:
2013/06/11 14:29:04 <0999> (725102) Processing batch 02_1231324
2013/06/11... (4 Replies)
Discussion started by: rpm120
4 Replies
LEARN ABOUT DEBIAN
nwbpset
NWBPSET(1) nwbpset NWBPSET(1) NAME
nwbpset - Create a bindery property or set its value SYNOPSIS
nwbpset [ -h ] [ -S server ] [ -U user name ] [ -P password | -n ] [ -C ] DESCRIPTION
nwbpset Reads a property specification from the standard input and creates and sets the corresponding property. The format is determined by the output of 'nwbpvalues -c'. nwbpset will hopefully become an important part of the bindery management suite of ncpfs, together with 'nwbpvalues -c'. See util/nwbpsecurity for an example. As another example, look at the following command line: nwbpvalues -t 1 -o supervisor -p user_defaults -c | sed '2s/.*/ME/'| sed '3s/.*/LOGIN_CONTROL/'| nwbpset With this command, the property user_defaults of the user object 'supervisor' is copied into the property login_control of the user object 'me'. nwbpvalues -t 1 -o me -p login_control -c | sed '9s/.*/ff/'| nwbpset This command disables the user object me. Feel free to contribute other examples! nwbpset looks up the file $HOME/.nwclient to find a file server, a user name and possibly a password. See nwclient(5) for more information. Please note that the access permissions of $HOME/.nwclient MUST be 600 for security reasons. OPTIONS
-h -h is used to print out a short help text. -S server server is the name of the server you want to use. -U user user is the user name to use for login. -P password password is the password to use for login. If neither -n nor -P are given, and the user has no open connection to the server, nwbpset prompts for a password. -n -n should be given if no password is required for the login. -C By default, passwords are converted to uppercase before they are sent to the server, because most servers require this. You can turn off this conversion by -C. AUTHORS
nwbpset was written by Volker Lendecke. See the Changes file of ncpfs for other contributors. nwbpset 8/7/1996 NWBPSET(1)