Sponsored Content
Full Discussion: installing scsi card
Top Forums UNIX for Dummies Questions & Answers installing scsi card Post 302178641 by tatacoffee on Wednesday 26th of March 2008 04:36:58 AM
Old 03-26-2008
installing scsi card

i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me.
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

help installing Sun 8mm unipack scsi tape drive

Hi all, please help I am stuck. I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies

2. UNIX for Dummies Questions & Answers

Installing a SCSI controller... problems

Hi, I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions? Thanks (2 Replies)
Discussion started by: nattie_h
2 Replies

3. UNIX for Advanced & Expert Users

Ultra 3 scsi card

Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say: pcipsy0: This is block Can someone please help me. I trying to hook... (2 Replies)
Discussion started by: aojmoj
2 Replies

4. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies

5. Solaris

Trouble Installing a SCSI Adapter

Okay. I admit I'm sort of a newbie in this regard. I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing. ... (3 Replies)
Discussion started by: Plain Person
3 Replies

6. SCO

configure Adaptec 29320ALP Ultra 320 SCSI Card in IBM X3400

I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies

7. SCO

Installing SCSI Tape drive

Hello, I'm having some issues with installing SCSI tape drive on SCO 5.0.6 hardware config shows the following adapters %adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto %adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd %adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies

8. UNIX for Dummies Questions & Answers

Problems with SCSI card and tape drive

Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies

9. Solaris

Solaris 10 SCSI card question

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies

10. Filesystems, Disks and Memory

Installing SCSI

I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI. I can get as far as plugging it in on my own. Please help Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
CD-DRIVE(1)							   User Commands						       CD-DRIVE(1)

NAME
cd-drive - manual page for cd-drive version 0.83 i686-pc-linux-gnu SYNOPSIS
cd-drive OPTION... Shows CD-ROM drive characteristics. DESCRIPTION
-d, --debug=INT Set debugging to LEVEL -i, --cdrom-device[=DEVICE] show only info about CD-ROM device -q, --quiet Don't produce warning output -V, --version display version and copyright information and exit Help options: -?, --help Show this help message --usage Display brief usage message AUTHOR
Rocky Bernstein rocky@gnu.org COPYRIGHT
Copyright (C) 2003, 2004, 2005, 2007, 2008, 2011 R. Bernstein This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. Have driver: GNU/Linux ioctl and MMC driver Have driver: cdrdao (TOC) disk image driver Have driver: bin/cuesheet disk image driver Have driver: Nero NRG disk image driver Default CD-ROM device: /dev/scd0 SEE ALSO
cd-info(1) for information about the CD inside a CD-ROM. cd-drive version 0.83 i686-pc-linux-gnu October 2011 CD-DRIVE(1)
All times are GMT -4. The time now is 08:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy