I have a 1 GB jazz drive. The jazz disk is used daily, both at home and at work on my Win 98 Server. So, I have to keep it in vfat format, which is fine because Linux rocks and will read it no problem. :-) However, I can't just stick the disk in the drive and open up the jazz folder in my mnt... (2 Replies)
i'm prepping for my midterm, which i will bomb. i am scurrying to finish reading the final chapter before i get down into the review.
however, i came across something in chapter 8 - "mounting file systems" that has me really confused.
the text says the following:
then it goes on to... (2 Replies)
Presently I have mounted a disk as su. I believe only root can mount disks -- is this correct?
I had to run mozilla in the root account so I can download the new SuSE distribution to the new disk.
How can I mount the disk so non-root accounts can access the disk?
Thanks,
Siegfried (4 Replies)
I have a USB disk on a little NAS controller (NSLU2 running unslung 6.8) that I can access nicely with root with
mount -t cifs \\\\10.134.23.23\\DISK\ 2 /mnt/LKGD7F73A
However, when I run emacs from an user mode xterm prompt, emacs cannot read and write the files on /mnt/LKGD7F73A. Emacs can... (11 Replies)
In Solaris 8, when I boot to single user mode, mount a device and then reboot or init 0, the system unmount it automatically. However, in Solaris 10 it does not seem to do the same. Here is what I did:
{0} ok boot -s
# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0.... (11 Replies)
Hello,
I'm trying to remove the need to use sudo to mount (in particular, binding).
Modifying /etc/sudoers using visudo, I have tried:
%admin ALL=NOPASSWD: /usr/bin/mount
%admin ALL=NOPASSWD: /usr/bin/umountand
%admin ALL=(ALL) NOPASSWD: /usr/bin/mount
%admin ALL=(ALL) NOPASSWD:... (5 Replies)
Hello...
I've mounted a share using standard nomenclature for the NFS mount command with the following command line:
mount -t nfs -o rw {IP address1}:/ /mnt_for_70 / {IP address2}(rw)
mnt_for_70 is a mount point I created on {IP address2}
I'm confuse and want to be sure I use the... (1 Reply)
I have some questions:
1, I successfully mounted my usb drive with "sudo mount /dev/sdb1 /mnt", but I can't wirte, It says "read-only file system". But I can write it in windows.
2, After I umounted the usb drive the led of it still on, but not blinking. Is it safe to unplug it? How to let it's... (17 Replies)
Hi Folks,
Could anyone please assist me with the what could be the scenarios to test the file system mount/umount performance check in HPUX.
Thanks in advance,
Vaishey (5 Replies)
Discussion started by: Vaishey
5 Replies
LEARN ABOUT FREEBSD
msdosfs
MSDOSFS(5) BSD File Formats Manual MSDOSFS(5)NAME
msdosfs -- MS-DOS file system
SYNOPSIS
options MSDOSFS
DESCRIPTION
The msdosfs driver will permit the FreeBSD kernel to read and write MS-DOS based file systems.
The most common usage follows:
mount -t msdosfs /dev/ada0sN /mnt
where N is the partition number and /mnt is a mount point. Some users tend to create a /dos directory for msdosfs mount points. This helps
to keep better track of the file system, and make it more easily accessible.
It is possible to define an entry in /etc/fstab that looks similar to:
/dev/ada0sN /dos msdosfs rw 0 0
This will mount an MS-DOS based partition at the /dos mount point during system boot. Using /mnt as a permanent mount point is not advised
as its intention has always been to be a temporary mount point for floppy and ZIP disks. See hier(7) for more information on FreeBSD direc-
tory layout.
SEE ALSO mount(2), unmount(2), mount(8), mount_msdosfs(8), umount(8)AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD October 1, 2013 BSD
03-24-2008
