03-20-2008
10 More Discussions You Might Find Interesting
1. IP Networking
I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies
2. Solaris
Hello All,
I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. Solaris
Dear UNIX Gurus
I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it
Regards (4 Replies)
Discussion started by: girish.batra
4 Replies
5. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
6. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
7. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
8. AIX
Hi,
I know the concept of multipathing, but would like to know how to configure multipathing in AIX.
or software/driver is by default present in AIX??????
How to find out wheather multipathing is configured in AIX?????
Regards,
Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies
9. Solaris
hi,
just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
10. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
LEARN ABOUT DEBIAN
ns_skipurl
Ns_Url(3aolserver) AOLserver Library Procedures Ns_Url(3aolserver)
__________________________________________________________________________________________________________________________________________________
NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines
SYNOPSIS
#include "ns.h"
int
Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl)
int
Ns_ParseUrl(char *url, char **pprotocol, char **phost,
char **pport, char **ppath, char **ptail)
char *
Ns_RelativeUrl(char *url, char *location)
char *
Ns_SkipUrl(Ns_Request *request, int n)
_________________________________________________________________
DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl)
Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR.
Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail)
Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref-
erence in the passed-in pointers. The passed-in url will be modified.
Ns_RelativeUrl(url, location)
If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is
http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the
relative url in the passed-in url, or NULL if error. Will set errno on error.
Ns_SkipUrl(request, n)
Return a pointer n elements into the request's url.
SEE ALSO
nsd(1), info(n)
KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)