Sponsored Content
Full Discussion: solaris multipathing
Operating Systems Solaris solaris multipathing Post 302177288 by Perderabo on Thursday 20th of March 2008 02:51:38 PM
Old 03-20-2008
Solaris SAN Configuration and Multipathing Guide might have a bit more info than just that one man page.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Quick Poll: Solaris IP Multipathing

I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies

2. Solaris

Solaris IP Multipathing (IPMP) Help

Hello All, I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies

3. Solaris

Solaris IP Multipathing

Hi, I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation . I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2. Now is it possible to have IP Multipathing on each of the servers as follows ? ... (0 Replies)
Discussion started by: maadhuu
0 Replies

4. Solaris

Disable Inbuilt multipathing software of Solaris 10

Dear UNIX Gurus I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it Regards (4 Replies)
Discussion started by: girish.batra
4 Replies

5. Solaris

Solaris multipathing

Hai we using emc storage which is conneted to M5000 through san switch. we asign 13 luns but in server it is showing 22 luns. i enable the solaris multipathing (MPxIO) #more /kernel/drv/fp.conf in that file MPxio-disable=no #mpathadm list lu it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies

6. Solaris

Multipathing - problem

Hello, I turned on the server multipathing: # uname -a SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140 stmsboot -D fp -e And after a reboot the server, multipathing is not enable: # stmsboot -L stmsboot: MPxIO is not enabled stmsboot: MPxIO disabled # ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies

7. Red Hat

How to Cleanup Multipathing

I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist. # multipath -l mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX \_ round-robin 0 \_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies

8. AIX

Multipathing in AIX

Hi, I know the concept of multipathing, but would like to know how to configure multipathing in AIX. or software/driver is by default present in AIX?????? How to find out wheather multipathing is configured in AIX????? Regards, Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies

9. Solaris

ZeusIOPS multipathing failed Solaris 11

hi, just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies

10. Red Hat

Verify multipathing

I have a couple of questions regarding multipath. If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13 If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure? Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.12.1 2008-04-04 URI::URL(3)
All times are GMT -4. The time now is 03:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy