03-12-2008
That's strange, are you sure that the NICs are phisicaly OK, connected, not faulty ? Those are configuration files, and as soon as the system boots, it will look for them, but they have to be created first. Use modprobe to determine the state of NICs, or "ethtool"
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just installed Crux on my laptop, which means I'll have to configure /etc/rc.d/net to adapt to my wireless internet. When I ran Linux before, I connected through eth1. How should I configure the /etc/rc.d/net file accordingly?
Thanks for reading,
Octal. (0 Replies)
Discussion started by: Octal
0 Replies
2. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
3. Solaris
Hi Guys,
I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets. (1 Reply)
Discussion started by: kurva
1 Replies
4. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
5. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
6. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
7. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
8. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
9. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
10. Shell Programming and Scripting
Change IP to multiple servers based on a database file. Source ip file is not incremental.
# Source host
#cat hosts
server1
server2
server3
server4
server5
server6
# SOURCE file
#cat ip
Host IP Netmask GW
server1 192.0.0.1 ... (2 Replies)
Discussion started by: invinzin21
2 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)
NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO
ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)