03-12-2008
That's strange, are you sure that the NICs are phisicaly OK, connected, not faulty ? Those are configuration files, and as soon as the system boots, it will look for them, but they have to be created first. Use modprobe to determine the state of NICs, or "ethtool"
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just installed Crux on my laptop, which means I'll have to configure /etc/rc.d/net to adapt to my wireless internet. When I ran Linux before, I connected through eth1. How should I configure the /etc/rc.d/net file accordingly?
Thanks for reading,
Octal. (0 Replies)
Discussion started by: Octal
0 Replies
2. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
3. Solaris
Hi Guys,
I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets. (1 Reply)
Discussion started by: kurva
1 Replies
4. Ubuntu
hello,
first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me.
So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1.
but the traffic routing is nor working properly
i configured the 2 interfaces to be... (2 Replies)
Discussion started by: florin.bv
2 Replies
5. IP Networking
hellow everbody.
iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here:
i have edited:
etc/sysctl.conf
net.ipv4.ip_forward = 1
and i have edited iptables too
# iptables -t nat -A... (2 Replies)
Discussion started by: paruhang
2 Replies
6. Red Hat
I have a local network on dev eth0
Server has static IP of 10.0.0.1
Gateway is 10.0.0.1
and Dns is 10.0.0.1
I am using this network for imaging 500 plus computer...
Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I... (0 Replies)
Discussion started by: golpemortal
0 Replies
7. Red Hat
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
8. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
9. IP Networking
Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open).
I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give... (3 Replies)
Discussion started by: adrhc
3 Replies
10. Shell Programming and Scripting
Change IP to multiple servers based on a database file. Source ip file is not incremental.
# Source host
#cat hosts
server1
server2
server3
server4
server5
server6
# SOURCE file
#cat ip
Host IP Netmask GW
server1 192.0.0.1 ... (2 Replies)
Discussion started by: invinzin21
2 Replies
MY(4) BSD Kernel Interfaces Manual MY(4)
NAME
my -- Myson Technology Ethernet PCI driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device my
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_my_load="YES"
DESCRIPTION
The my driver provides support for various NICs based on the Myson chipset. The Myson chipset is a variant of the DEC Tulip NIC chipset.
The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error.
HARDWARE
The my driver provides support for various NICs based on the Myson chipset. Supported models include:
o Myson MTD800 PCI Fast Ethernet chip
o Myson MTD803 PCI Fast Ethernet chip
o Myson MTD89X PCI Gigabit Ethernet chip
SEE ALSO
altq(4), de(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The my driver first appeared in FreeBSD 4.6.
AUTHORS
The my driver was written by Myson Technology Inc.
This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>.
BUGS
The my driver does not support Power Management Events (PME).
BSD March 11, 2007 BSD