03-10-2008
Sprellarinn, you are absolutely right.
Here is the biggest help i can offer: read some documentation, then come back and ask educated questions.
-closed-
bakunin
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I recently had a disk crash and was not able to clean the dump lv off the disk. Now trying to create new lvdump I am running into errors.
My question is how do I remove the old lv out of the ODM? I have tried going through smit and also just rmlv and it cannot find the lv. Yet when I run lslv on... (0 Replies)
Discussion started by: Wamland
0 Replies
2. AIX
I have replace a couple of hdisks in and old AIX 4 system. I have them assigned to the hdisk numbers previously in the system. When I don an lsvg -p vgname, i see them old devices by device number still come up as missing. I think they are still in the ODM,, how can I remove them?
Thanks
Mike (5 Replies)
Discussion started by: mhenryj
5 Replies
3. AIX
Hi Everyone,
I would like to know if its possible to create a 2 copy mirror using LVM with 1 member a FC attached disk and the other an iscsi disk.
Will LVM let me mirror to two different disk types?
I know there will be issues doing this however it is only a short term solution until we... (1 Reply)
Discussion started by: bizman
1 Replies
4. AIX
Hi All,
I remove the default gateway by using a command line but I need also to remove it from ODM so that reboot will not trigger it back.
How do I remove it from ODM of AIX 5.3?
Thanks for any comment you may add. (4 Replies)
Discussion started by: itik
4 Replies
5. HP-UX
Hi,
I'm new to HP-UX.
I have LVM on /var with 92Gig. I would like to reduce it to create another LVM for Oracle client with 800 meg or so. How to do it. I'm running 11.iv3
Thanks (4 Replies)
Discussion started by: lamoul
4 Replies
6. AIX
Hi,
I gonna try to explain my problem.
When I list my tty I have something like that:
sa3 is the RAN where the tty are connected.
Yesterday I tried to delete every tty from the RAN
I had a problem with a tty which was not possible to delete with rmdev -dl, so I had to :
- delete it... (0 Replies)
Discussion started by: Castelior
0 Replies
7. AIX
Please consider this a question about basics&best practices. On AIX 5.3 system, three raw physical volumes are defined from storage. While doing a read with command dd from the raw device, the speed rate is 250Mb/s.
Then, it gets complex when I define these three pv's to an lv of type raw. Doing... (4 Replies)
Discussion started by: royalliege
4 Replies
8. AIX
Hello!
I did a big mistake and now I have to change the ODM base manually :wall:
I had a server of test with 2 VG (rootvg and datavg). I had to test something on it with an other AIX version. So, to be sure to restore it, i did a mksysb before but I had completly forgotten the second vg and... (1 Reply)
Discussion started by: Castelior
1 Replies
9. UNIX for Dummies Questions & Answers
Hi Guys,
I m using redhat 6, I have installed root partition as non-LVM .
Is there any way i can convert it to LVM? (1 Reply)
Discussion started by: pinga123
1 Replies
10. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT DEBIAN
colorgccrc
COLORGCCRC(5) File Formats Manual COLORGCCRC(5)
NAME
colorgccrc - configuration file for colorgcc
DESCRIPTION
A colorgccrc configuration file is used to configure the highlighting of the compiler output from colorgcc.
SYNTAX
Each line consists of a keyword designating a configuration variable. The keyword is followed by `:' and then one or several values
(depending on the keyword). Lines beginning with a hash mark `#' are comments.
CONFIGURATION VARIABLES
g++ | gcc | c++ | cc | g77 | gcj | gnat | gpc
Specifies the paths to the compilers. Takes one value; a path to the compiler.
nocolor
Specifies what terminal types colorization should be disabled on. Takes one or several values, separated by whitespace.
srcColor
Specifies the highlighting attributes source-code should be given. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
introColor
Specifies the highlighting attributes for normal compiler output. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
warningFileNameColor | errorFileNameColor
Specifies the highlighting attributes for the filename in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningNumberColor | errorNumberColor
Specifies the highlighting attributes for the line-number in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningMessageColor | errorMessageColor
Specifies the highlighting attributes for the message-text in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
COLOR ATTRIBUTES
The following attributes are valid for highlighting.
clear, reset
bold, underline, underscore, blink, reverse, concealed
black, red, green, yellow, blue, magenta, cyan, white
on_black, on_red, on_green, on_yellow, on_blue, on_magenta, on_cyan, on_white
SEE ALSO
gcc(1), colorgcc(1)
HISTORY
Jan 15 2003: Initial version of this manual-page.
REPORTING BUGS
Report bugs to <jmoyers@geeks.com>
AUTHORS
Jamie Moyers <jmoyers@geeks.com> is the author of colorgcc.
This manual page was written by Joe Wreschnig <piman@sacredchao.net>, and modified by David Weinehall <tao@debian.org>, for the Debian
GNU/Linux system (but may be used by others).
COPYRIGHT
Copyright (C) 2003 Jamie Moyers
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
Jan 15, 2003 COLORGCCRC(5)