I have a 1 GB jazz drive. The jazz disk is used daily, both at home and at work on my Win 98 Server. So, I have to keep it in vfat format, which is fine because Linux rocks and will read it no problem. :-) However, I can't just stick the disk in the drive and open up the jazz folder in my mnt... (2 Replies)
i'm prepping for my midterm, which i will bomb. i am scurrying to finish reading the final chapter before i get down into the review.
however, i came across something in chapter 8 - "mounting file systems" that has me really confused.
the text says the following:
then it goes on to... (2 Replies)
Presently I have mounted a disk as su. I believe only root can mount disks -- is this correct?
I had to run mozilla in the root account so I can download the new SuSE distribution to the new disk.
How can I mount the disk so non-root accounts can access the disk?
Thanks,
Siegfried (4 Replies)
I have a USB disk on a little NAS controller (NSLU2 running unslung 6.8) that I can access nicely with root with
mount -t cifs \\\\10.134.23.23\\DISK\ 2 /mnt/LKGD7F73A
However, when I run emacs from an user mode xterm prompt, emacs cannot read and write the files on /mnt/LKGD7F73A. Emacs can... (11 Replies)
In Solaris 8, when I boot to single user mode, mount a device and then reboot or init 0, the system unmount it automatically. However, in Solaris 10 it does not seem to do the same. Here is what I did:
{0} ok boot -s
# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0.... (11 Replies)
Hello,
I'm trying to remove the need to use sudo to mount (in particular, binding).
Modifying /etc/sudoers using visudo, I have tried:
%admin ALL=NOPASSWD: /usr/bin/mount
%admin ALL=NOPASSWD: /usr/bin/umountand
%admin ALL=(ALL) NOPASSWD: /usr/bin/mount
%admin ALL=(ALL) NOPASSWD:... (5 Replies)
Hello...
I've mounted a share using standard nomenclature for the NFS mount command with the following command line:
mount -t nfs -o rw {IP address1}:/ /mnt_for_70 / {IP address2}(rw)
mnt_for_70 is a mount point I created on {IP address2}
I'm confuse and want to be sure I use the... (1 Reply)
I have some questions:
1, I successfully mounted my usb drive with "sudo mount /dev/sdb1 /mnt", but I can't wirte, It says "read-only file system". But I can write it in windows.
2, After I umounted the usb drive the led of it still on, but not blinking. Is it safe to unplug it? How to let it's... (17 Replies)
Hi Folks,
Could anyone please assist me with the what could be the scenarios to test the file system mount/umount performance check in HPUX.
Thanks in advance,
Vaishey (5 Replies)
Discussion started by: Vaishey
5 Replies
LEARN ABOUT CENTOS
locale::codes::langext
Locale::Codes::LangExt(3) User Contributed Perl Documentation Locale::Codes::LangExt(3)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.3 2013-02-27 Locale::Codes::LangExt(3)