02-21-2008
Thanks for your help
I configured it to the wrong SCSI Card, it was on the same SCSI device as the disks.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
2. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
3. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
4. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
5. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
6. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
7. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
i installed a unix tape drive on my alphaserver. when i use a mt command it tells me there is no tape or device.
I have used the hardware manager and it shows the tape is present.
Can anyone help me understand why it cannot pick up the tape as a default? (1 Reply)
Discussion started by: ryks
1 Replies
9. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
10. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
LEARN ABOUT MINIX
scsi_address
scsi_address(9S) Data Structures for Drivers scsi_address(9S)
NAME
scsi_address - SCSI address structure
SYNOPSIS
#include <sys/scsi/scsi.h>
INTERFACE LEVEL
Solaris architecture specific (Solaris DDI)
DESCRIPTION
A scsi_address structure defines the addressing components for a SCSI target device. The address of the target device is separated into two
components: target number and logical unit number. The two addressing components are used to uniquely identify any type of SCSI device;
however, most devices can be addressed with the target component of the address.
In the case where only the target component is used to address the device, the logical unit should be set to 0. If the SCSI target device
supports logical units, then the HBA must interpret the logical units field of the data structure.
The pkt_address member of a scsi_pkt(9S) is initialized by scsi_init_pkt(9F).
STRUCTURE MEMBERS
scsi_hba_tran_t *a_hba_tran; /* Transport vectors for the SCSI bus */
ushort_t a_target; /* SCSI target id */
uchar_t a_lun; /* SCSI logical unit */
a_hba_tran is a pointer to the controlling HBA's transport vector structure. The SCSA interface uses this field to pass any transport
requests from the SCSI target device drivers to the HBA driver.
a_target is the target component of the SCSI address.
a_lun is the logical unit component of the SCSI address. The logical unit is used to further distinguish a SCSI target device that supports
multiple logical units from one that does not. The makecom(9F) family of functions use the a_lun field to set the logical unit field in the
SCSI CDB, for compatibility with SCSI-1.
SEE ALSO
makecom(9F), scsi_init_pkt(9F), scsi_hba_tran(9S), scsi_pkt(9S)
Writing Device Drivers
SunOS 5.10 30 Aug 1995 scsi_address(9S)