02-20-2008
do as already suggested... replace the disk with the same disk...
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I have the situaiton in which primary boot disk has bad sectors in Solaris 9. The other hard disk is mirrored using Solstice DiskSuite 4.2. I can reboot system with the other disk. My question is, when I replaced the boot disk with a new one, how can I create meta db and finally make it... (2 Replies)
Discussion started by: s_aamir
2 Replies
2. Solaris
Hi,
We had a disk go bad in this SunFire 280R, running Solaris 8 - Generic_117350-46. We replaced the disk and partitioned it. We metadetached all the metadevices but for some reason the new disk is showing up in the metadb as Concat/Stripe and it won't let us re-sync the mirror. We are not... (2 Replies)
Discussion started by: mgb
2 Replies
3. Solaris
The following is the summarry:-
1) Four disks in server ie (c1t0d0. c1t1d0, c1t2d0, c1t3d0). c1t2d0 is the disk to be replaced.
c1t0d0 and c1t2d0 are mirrors.
c1t1d0 and c1t3d0 are mirrors.
Metadb to be deleted is in c1t2d0s7
a) Mirror d35 has 2 submirrors d38 and d39
d38 is a stripe... (0 Replies)
Discussion started by: aji1729
0 Replies
4. AIX
Hi Admins,
I am new into aix.I was surfing aix pages and reading how to replace failed mirror disks.I read in one of the posts that we have to reboot the server to replace the disk. actually i was a HPUX admin and many times replaced root mirror disk online.Ofcourse it was hot swappable.
... (2 Replies)
Discussion started by: newaix
2 Replies
5. AIX
First a little background: I'm working with an AIX 6.1 TL05 running two mirrored SAS disks (rootvg) and four SSDs (appvg)
All four SSDs belong to appvg and are setup to mirror as follows:
hdisk4 --> hdisk6 (containing application fs)
hdisk5 --> hdisk7 (containing database fs)
A few days... (1 Reply)
Discussion started by: Michael Mullig
1 Replies
6. Solaris
I have a v480 with a mirrored boot disk c1t0 and c1t1. The drives themselves don't show a failure but the mirror's need maintenance.
This is my plan for replacing the drive. I would love feedback to point out what I"m missing or where my steps are incorrect.
Two things I believe I'm... (3 Replies)
Discussion started by: pcoffey
3 Replies
7. Solaris
Hi All
BAsed on the below I would like to verifu two things
(1) The udnerlying mirroris for '/mnt' na dit onlcy contaisne 1 sub-mirror, with one sliceon is one disk and hence, data loss on the mount point (the mount point, '/mnt' is backed up)
(2) the Procedure for renewal
# df -kh /mnt... (2 Replies)
Discussion started by: stevie_velvet
2 Replies
8. Solaris
Hi
Please can you help me on replacing or removing a faulty disk drive on a SUN NETRA X4250server with 4 internal drives only.
the format comand show me the following:
format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <drive type unknown>
... (9 Replies)
Discussion started by: fretagi
9 Replies
LEARN ABOUT OSF1
volreattach
volreattach(8) System Manager's Manual volreattach(8)
NAME
volreattach - Reattaches disk drives that have once again become accessible
SYNOPSIS
/usr/sbin/volreattach [-rb] [accessname...]
/usr/sbin/volreattach -c accessname
OPTIONS
The volreattach utility has the following options: Calls the volrecover utility to attempt to recover stale plexes of any volumes on the
failed disk. Performs the reattach operation in the background. Checks whether a reattach is possible. No operation is performed, but the
name of the disk group and disk media name at which the disk can be reattached is displayed.
DESCRIPTION
The volreattach utility attempts to reattach disks using the same disk group and media names they had before detachment.
This operation may be necessary if a disk has a transient failure, or if some disk drivers are unloaded or unloadable when the Logical
Storage Manager is started, causing disks to enter the failed state.
If the problem is fixed, the volreattach command can be used to reattach the disks without plexes being flagged as stale, as long as the
reattach happens before any volumes on the disk are started.
The volreattach command is called from the voldiskadm menus as part of disk recovery.
The volreattach utility tries to find a disk with a disk group and disk ID matching that of the disk(s) being reattached. If the matching
disk is found, the reattach operation may still fail if the original cause (or some other cause) for the disk failure still exists.
EXIT CODES
A zero exit status is returned if it is possible to perform a reattach. Otherwise, non-zero is returned.
SEE ALSO
volintro(8), voldiskadm(8), volrecover(8)
volreattach(8)