02-14-2008
hi.
pls help me ! how to add USB printer in sco open server 6 , printer is parallel port but mother board dont have a parallel port , how can we configure this printer ??
8 More Discussions You Might Find Interesting
1. HP-UX
I want to add printer on a serial port can I get full details of all parameters like baudrate, parity,flow control, ...
Thanks (1 Reply)
Discussion started by: Hegazy Mahdy
1 Replies
2. IP Networking
Does anybody know how to add a printer from network in Solaris 10 using IP settings? according to our IT support, in order to add this printer in Windows XP we introduce it as a local printer which is connected to a port with an IP address, like 128.79.44.110. Anyway I don't know how it can be done... (3 Replies)
Discussion started by: arash05
3 Replies
3. AIX
Hello
Let me first give a small overview of the setup. All printers are connected to Windows 2000 servers. There are a lot of UNIX (AIX & HP-UX) servers as well which have SAP running.
I'm working on a script to add printers to a specified SAP instance. I want to verify the user input (to... (0 Replies)
Discussion started by: NielsV
0 Replies
4. OS X (Apple)
Hey, im new to processing so any help you could give me would be much appreciated.
I am trying to get control of the rollers on my 9 pin dot matrix printer (epson LX 300+). Initially I was going to do this through arduino but hope to do it through processing using the serialwrite programme.
... (0 Replies)
Discussion started by: hougeman
0 Replies
5. SCO
Dear Sir,
How can install additional pci lpt card (parallel port)
I want to install second dmp printer in unixware 7 server
thanks n regards (2 Replies)
Discussion started by: sudhir69
2 Replies
6. IP Networking
I have a number of Windows CE operator terminals. They have facility to print alarms/messages to ...
aser or Inkjet (so they're using PCL).
USB or IP. IP connection takes just the IP address.
Question
How could I create a service or daemon on a server to capture all this data?... (7 Replies)
Discussion started by: transistor
7 Replies
7. HP-UX
Hi ,
Is there any way to check what is the port used by lp remote printer in hpux ? (1 Reply)
Discussion started by: nanduri
1 Replies
8. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LPT(4) BSD Kernel Interfaces Manual LPT(4)
NAME
lpt -- generic printer device driver
SYNOPSIS
device ppc
device ppbus
device lpt
DESCRIPTION
The current lpt driver is the port of the original lpt driver to the ppbus(4) system.
One purpose of this port was to allow parallel port sharing with other parallel devices. Secondly, inb()/outb() calls have been replaced by
ppbus function calls. lpt is now arch-independent thanks to the ppbus interface. See ppbus(4) for more info about the ppbus system.
The parallel port bus is allocated by lpt when the printer device is opened and released only when the transfer is completed: either when the
device is closed or when the entire buffer is sent in interrupt driven mode.
The driver can be configured to be either interrupt-driven, or to poll the printer. Ports that are configured to be interrupt-driven can be
switched to polled mode by using the lptcontrol(8) command.
Depending on your hardware, extended capabilities may be configured with the lptcontrol(8) command. With an ECP/ISA port, you can take
advantage of FIFO and DMA.
In order to retrieve printer info from /dev/lpt0, just apply the cat command to the device. If the printer supports IEEE1284 nibble mode and
has data to send to the host, you will get it.
FILES
/dev/lpt0 first parallel port driver
SEE ALSO
ppbus(4), ppc(4), lptcontrol(8)
HISTORY
This driver replaces the functionality of the lpa driver, which is now defunct.
BUGS
There are lots of them, especially in cheap parallel port implementations.
It is only possible to open a lpt port when a printer is connected and on-line, making it impossible to run lptcontrol(8) when there is no
printer connected.
This driver could still stand a rewrite.
BSD
February 14, 1999 BSD