Sponsored Content
Top Forums UNIX for Dummies Questions & Answers run command Unix on a single line Post 302164254 by Dave Miller on Monday 4th of February 2008 10:21:17 AM
Old 02-04-2008
Wouldn't a semicolon work?

I.E. Usually you can put multiple commands on a single line by seperating them with a semicolon:

command [argument] ; command [argument] ; command [argument] ... etc.
is the same as:
command [argument] <NL>
command [argument] <NL>
command [argument] <NL>
...
etc.

NOTE:

The vertical bar you used, usually called 'Pipe', does NOT seperate commands the same way. It is used to direct the output of one command to be used as the input of the next command. I'm fairly certain that using it as you indicated would not work at all, unless the first command had output that the second command could use.
 

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

single line command

i need to search for a single pattern in three different logs....what would be the best one line script???? (4 Replies)
Discussion started by: roshanjain2
4 Replies

2. UNIX for Dummies Questions & Answers

How to run multiple command in single command?

Dear Unix Guru, I have several directories as below /home/user/ dir1 dir2 dir3 Each directory has different size. I want to print each directory size (Solaris command du -hs .) Can you please guide me how to achieve this? Thanks Bala (2 Replies)
Discussion started by: baluchen
2 Replies

3. UNIX for Advanced & Expert Users

unix command for terminal - view sequences as a single line?

Hello, I'm looking for some code that will list sequences of files as a single line. ie, sequences of files like this: filename.1.ext filename.2.ext filename.3.ext filename.4.ext filename.5.ext filename.6.ext filename.7.ext filename.8.ext filename.9.ext filename.10.ext would... (6 Replies)
Discussion started by: kentm
6 Replies

4. Solaris

Single maintence mode cannot run any command on M4000

Hii All I was building two M4000 servers and one was successfully installed. Other one /usr has been unmounted. my putty session got disconnected and i connected to console where it asked for root single maintence # # init 0 not foung # df -h not found # xscf>poweroff -a xscf>... (8 Replies)
Discussion started by: seems
8 Replies

5. UNIX for Dummies Questions & Answers

How to run multiple command in a single line?

Normally i would do this- cd abc ls -ltr I wish to run above command in a single line, like this- cd abc | ls -ltr But above command doesn't works, it simply runs the second command, ignoring the 1st one. :confused: (4 Replies)
Discussion started by: boy18nj
4 Replies

6. Shell Programming and Scripting

sed command to grep multiple pattern present in single line and delete that line

here is what i want to achieve.. i have a file with below contents cat fileName blah blah blah . .DROP this REJECT that . --sport 7800 -j REJECT --reject-with icmp-port-unreachable --dport 7800 -j REJECT --reject-with icmp-port-unreachable . . . more blah blah blah --dport 3306... (14 Replies)
Discussion started by: vivek d r
14 Replies

7. Shell Programming and Scripting

Su and run single line command

myenv.sh script sets LOG_DIR variable. I can run the script and echo the variable in a single line as: # First set LOG_DIR to some dummy 'NONE' value $ export LOG_DIR="NONE" $ echo ${LOG_DIR} NONE $ cat /tmp/bin/myenv.sh export LOG_DIR="/tmp/log" #The below command doesn't show the... (2 Replies)
Discussion started by: ysrini
2 Replies

8. UNIX for Dummies Questions & Answers

To find and display the middle line in a file using single line command.

Hi all, How can i display the middle line of a file using a single line command? (6 Replies)
Discussion started by: Lakme Pemmaiah
6 Replies

9. Solaris

Can I run repair on lot of blocks with single command ?

Hi, I have Solaris-10 OS on T5220. Both local disks were mirrored under SVM. Somehow when one disk gone bad (c0t1d0), other disk (c0t0d0) also got lot of bad block. We have readable data only on c0t0d0, but as soon as server comes after, it hangs when I run few commands because of read errors,... (1 Reply)
Discussion started by: solaris_1977
1 Replies

10. Shell Programming and Scripting

How to run simple single command on multiple Linux servers?

Hi All, How can i run a single command on multiple servers with or without giving credentials. I have a file(servers.txt) which has got list of servers and i want to run a command lsb_release -dr on all these servers and get output of those servers against each server. I tried below code... (9 Replies)
Discussion started by: darling
9 Replies
command(1)						      General Commands Manual							command(1)

NAME
command - execute a simple command SYNOPSIS
command_name [argument ...] DESCRIPTION
enables the shell to treat the arguments as a simple command, suppressing the shell function lookup. If command_name is not the name of the function, the effect of is the same as omitting command. Operands recognizes the following operands: command_name The name of a HP-UX command or a shell built-in command. argument One or more strings to be interpreted as arguments to command_name. The command is necessary to allow functions that have the same name as a command to call the command (instead of a recursive call to the function). Nothing in the description of is intended to imply that the command line is parsed any differently than any other simple command. For example, is not parsed in any special way that causes or to be treated other than a pipe operator or semicolon or that prevents function lookup on b or c. EXTERNAL INFLUENCES
Environment Variables determines the search path used during the command search. RETURN VALUE
exits with one of the following values: o If fails: 126 The utility specified by the command_name is found but not executable. 127 An error occurred in the utility or the utility specified by command_name is not found. o If does not fail: The exit status of is the same as that of the simple command specified by the arguments: command_name[argument ...] EXAMPLES
Create a version of the command that always prints the name of the new working directory whenever it is used: cd() { command "$@" >/dev/null pwd } Circumvent the redefined command above, and change directories without printing the name of the new working directory: SEE ALSO
getconf(1), sh-posix(1), confstr(3C). STANDARDS CONFORMANCE
command(1)
All times are GMT -4. The time now is 04:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy