Sponsored Content
Operating Systems Solaris assigning ip to second interface Post 302164174 by DukeNuke2 on Monday 4th of February 2008 05:29:53 AM
Old 02-04-2008
hmm, if no output is shown... do you know what interface you have? what kind of mashine is it (uname -a) an is it an internal interface or an extension card?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

assigning variables

Before I even attempt this, is it possible to grep for a pattern, maybe a partial sentence like "go to page 3", assign that to a variable and then use awk or something to pull out the 3 and assign it to a variable? So first I would have Gotopg = "go to page 3" then page = 3 (9 Replies)
Discussion started by: k@ssidy
9 Replies

2. HP-UX

Assigning IP's

hi all, i want to know where i can add and IP address so when i do a "w", i can see what IP is assigned to which tty? i know in tru64 you just added an entry to /etc/hosts. this does not seem to be the case with hpux. thanks (12 Replies)
Discussion started by: macgre_r
12 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

6. Shell Programming and Scripting

Assigning variables

i have variables RECIPIENTS_DEVL,RECIPIENTS_UACC,RECIPIENTS_PROD i have a case statement to get the phase variable: case ${WMD_UPHASE1} in u) WMD_UPHASE4=UACC;; i) WMD_UPHASE4=DEVL;; p) WMD_UPHASE4=PROD;; d) WMD_UPHASE4=DEVL;; *) WMD_UPHASE4=DEVL;; esac I am unable to... (3 Replies)
Discussion started by: Arun Mishra
3 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies

9. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
dr(7d)								      Devices								    dr(7d)

NAME
dr, drmach, ngdr, ngdrmach - Sun Enterprise 10000 dynamic reconfiguration driver SYNOPSIS
dr drmach ngdr ngdrmach DESCRIPTION
The dynamic reconfiguration (DR) driver consists of a platform-independent driver and a platform-specific module. The DR driver uses stan- dard features of the Solaris operating environment whenever possible to control DR operations and calls the platform specific module as needed. The DR driver creates minor nodes in the file system that serve as attachment points for DR operations. The DR driver provides a pseudo-driver interface to sequence attach and detach operations on system boards using file system entry points referred to as "attachment points." The attachment point form depends on the platform. Sun Enterprise 10000 Server On the Sun Enterprise 10000 server, the DR driver consists of a platform-independent driver (ngdr) and a platform-specific module (ngdr- mach). The domain configuration server (DCS) accepts DR requests from the system services processor (SSP) and uses the libcfgadm(3LIB) interface to initiate the DR operation. After the operation is performed, the results are returned to the SSP. For more information about the DCS on the Sun Enterprise 10000, refer to the dcs(1M) man page and the Sun Enterprise 10000 Dynamic Reconfiguration User Guide. The DR driver creates physical attachment points for system board slots that takes the following form: /devices/pseudo/ngdr@0:SBx Where x represents the slot number (0 to 15) for a particular board. The cfgadm_sbd(1M) plugin creates dynamic attachment points that refer to components on system boards, including CPUs, memory, or I/O devices. Refer to the cfgadm_sbd(1M) man page for more details. SEE ALSO
cfgadm_sbd(1M), ioctl(2), libcfgadm(3LIB) Sun Enterprise 10000 Dynamic Reconfiguration User Guide SunOS 5.10 29 Sep 2003 dr(7d)
All times are GMT -4. The time now is 09:19 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy