01-31-2008
Just make installpkg ad320, after relinking system on reboot it doesn't appear as an adapter, and later a run mkdev tape with host 0, id apater 4 lun 0 and bus 0, and it deosn't appear on kernel's boot, as a hardware, any other idea??, by the way anyone know wich kind of parallel port works with this server ML 350 G5, the scsi card 29320ALP is pcx and i put it on the slot of pcx of the server the boot bios recognice it but the unix kernel doesn't reflect the installation of it, afet using installpkg neither using mkdev tape commands, thx for your help and for your answer
10 More Discussions You Might Find Interesting
1. Linux
Hi,
I want to install LINUX on my laptop. I have a 2GHZ,1GB RAM and HDD is not partitioned. I donot want to touch this HDD and I have external HDD of 200GB. Can I install LINUX on this external HDD?. I would like system to detect linux only when I connect my external hard drive. else system should... (5 Replies)
Discussion started by: sureshht
5 Replies
2. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
3. SCO
Hi there
We are trying to install SCO OpenServer v5.07 on an HP ML350 G5 server.
I have downloaded the drivers from HP's website, but are getting nowhere. (I feel that I am going round in circles - every time I google for the drivers, I end up here.) :(
What happens is we create the driver... (12 Replies)
Discussion started by: The_Librarian
12 Replies
4. Solaris
I am looking for this document UNIX Configuration Guide on the HP StorageWorks Tape.
I need a procedure to install StorageWorks DAT 40 internal tape drive C5668A. (10 Replies)
Discussion started by: real-chess
10 Replies
5. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
6. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
7. Solaris
i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10.
Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6.
while reading through the user guide i got pretty confuse.
... (1 Reply)
Discussion started by: monstar1407
1 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. OS X (Apple)
Hi,
As I did not find any specific group for this question, i am putting it here.
Can I install Mac OS on an external hard disk?
Is this possible or not? I know it is very hard to install mac os on non-mac hardwares. I have a dell inspiron laptop and i want to use mac from external hdd.
... (1 Reply)
Discussion started by: sanzee
1 Replies
10. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
LEARN ABOUT CENTOS
amcleanup
AMCLEANUP(8) System Administration Commands AMCLEANUP(8)
NAME
amcleanup - run the Amanda cleanup process after a failure
SYNOPSIS
amcleanup [-k] [-p] [-r] [-v] config
DESCRIPTION
Amcleanup generates the Amanda Mail Report and updates the Amanda databases after a system failure on a tape server host. This cleanup
process is normally done automatically as part of the amdump program, but if amdump cannot complete for some reason (usually because of a
tape server host crash), amcleanup must be run some time later (usually during system boot).
The amcleanupdisk program is run with the same [-r] and [-v] options.
See the amanda(8) man page for more details about Amanda.
OPTIONS
-k
Kill all process listed in the log file are their child. if there is no log file, then kill all amdump and amflush process and their
child.
-p
Do the cleanup only if all process listed in the log file are already terminated.
-r
Remove bad file in holding disk. This options is passed to amcleanupdisk.
-v
Generate verbose output. This options is passed to amcleanupdisk.
EXAMPLES
This example runs the Amanda cleanup process by hand after a failure.
% amcleanup daily
Putting the following line in a system boot script (e.g. /etc/rc.local) runs the Amanda cleanup process as part of the reboot, eliminating
the need to run it by hand.
/usr/local/sbin/amcleanup daily
If nothing needs to be done, amcleanup exits normally with the message:
amcleanup: no unprocessed logfile to clean up.
SEE ALSO
amanda(8), amdump(8)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHORS
James da Silva <jds@amanda.org>
Stefan G. Weichinger <sgw@amanda.org>
Amanda 3.3.3 01/10/2013 AMCLEANUP(8)