01-27-2008
I can get to the ALOM and type a username/password in that, which obviously doesn't help me as I don't have these details. After a minute of so or not typing in the ALOM, I get a timeout and am sent back to the serial console where as I mentioned I cannot type anything.
I haven't tried the built-in (DB9 connector) serial port yet - hopefully I can find the right console cable for this.
10 More Discussions You Might Find Interesting
1. Solaris
I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies
2. Solaris
I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies
3. Solaris
I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440.
I would like to avoid reinstall on the V440 for many reasons.
Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies
4. Solaris
Hello everyone,
I'm here today looking for help...
I have a SunFire v440 running Solaris 9 at work that manages the SCSI tape drives(LTO3) in our L700 tape library (runs SAMFS).
I went into work today and found the machine was ping-able but I could not connect to it via SSH and could not... (7 Replies)
Discussion started by: mainegeek
7 Replies
5. Solaris
I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies
6. Solaris
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies
7. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
8. Solaris
Hi,
I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file.
... (1 Reply)
Discussion started by: samnyc
1 Replies
9. UNIX for Dummies Questions & Answers
how to Change the % prompt to - prompt in unix
:wall:
---------- Post updated at 07:40 AM ---------- Previous update was at 07:38 AM ----------
How To display the last modification time of any file in unix
---------- Post updated at 07:40 AM ---------- Previous update was at 07:40 AM... (2 Replies)
Discussion started by: manjiri sawant
2 Replies
10. Solaris
Hi,
on sunfire v890 unable to move from rsc prompt to ok prompt, i have executed the command break. (9 Replies)
Discussion started by: manoj.solaris
9 Replies
LEARN ABOUT CENTOS
des_read_2passwords
ui_compat(3) OpenSSL ui_compat(3)
NAME
des_read_password, des_read_2passwords, des_read_pw_string, des_read_pw - Compatibility user interface functions
SYNOPSIS
#include <openssl/des_old.h>
int des_read_password(DES_cblock *key,const char *prompt,int verify);
int des_read_2passwords(DES_cblock *key1,DES_cblock *key2,
const char *prompt,int verify);
int des_read_pw_string(char *buf,int length,const char *prompt,int verify);
int des_read_pw(char *buf,char *buff,int size,const char *prompt,int verify);
DESCRIPTION
The DES library contained a few routines to prompt for passwords. These aren't necessarely dependent on DES, and have therefore become
part of the UI compatibility library.
des_read_pw() writes the string specified by prompt to standard output turns echo off and reads an input string from the terminal. The
string is returned in buf, which must have spac for at least size bytes. If verify is set, the user is asked for the password twice and
unless the two copies match, an error is returned. The second password is stored in buff, which must therefore also be at least size
bytes. A return code of -1 indicates a system error, 1 failure due to use interaction, and 0 is success. All other functions described
here use des_read_pw() to do the work.
des_read_pw_string() is a variant of des_read_pw() that provides a buffer for you if verify is set.
des_read_password() calls des_read_pw() and converts the password to a DES key by calling DES_string_to_key(); des_read_2password()
operates in the same way as des_read_password() except that it generates two keys by using the DES_string_to_2key() function.
NOTES
des_read_pw_string() is available in the MIT Kerberos library as well, and is also available under the name EVP_read_pw_string().
SEE ALSO
ui(3), ui_create(3)
AUTHOR
Richard Levitte (richard@levitte.org) for the OpenSSL project (http://www.openssl.org).
1.0.1e 2013-02-11 ui_compat(3)