Sponsored Content
Full Discussion: Can't get ok prompt on V440
Operating Systems Solaris Can't get ok prompt on V440 Post 302161966 by juanj on Sunday 27th of January 2008 09:03:09 AM
Old 01-27-2008
Can't get ok prompt on V440

Hello all,

This is probably a commonly asked question, but it has me stumped.

I have a V440 which upon bootup gives me the option of getting into ALOM with #. I don't have the ALOM password so I want to re-install Solaris 10.

When connected to the Management serial interface (on the PCI card) with either Hyperterminal or Terraterm, I cannot get to the ok prompt. I send a break and am given the following on the console:

SC Alert: SC request to send break to host

At this point I would expect the ok prompt. However, I am not given this, and am not able to type anything - just given a blinking cursor. The only thing I can do is send another break, upon which I am given the same message above, or type #. to get back to ALOM.

Is there anything else I can try to get the ok prompt? It seems the boot device is the hard disk as well, not the cdrom, so I can't install that way either.

Thanks in advance.
 

10 More Discussions You Might Find Interesting

1. Solaris

video card for a V440

I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies

2. Solaris

SUN V440 Question

I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies

3. Solaris

V210 to V440

I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440. I would like to avoid reinstall on the V440 for many reasons. Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies

4. Solaris

Need ideas what is wrong with v440

Hello everyone, I'm here today looking for help... I have a SunFire v440 running Solaris 9 at work that manages the SCSI tape drives(LTO3) in our L700 tape library (runs SAMFS). I went into work today and found the machine was ping-able but I could not connect to it via SSH and could not... (7 Replies)
Discussion started by: mainegeek
7 Replies

5. Solaris

V210 to V440

I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies

6. Solaris

Boot issues Solaris 10 + V440

Hello, I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message: Sun Fire V440, No Keyboard Copyright 2007 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies

7. Solaris

available PCI slots on v440

How do I find any available PCI slots on a v440? When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used. ================================= IO Devices ================================= Bus Freq Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies

8. Solaris

Solaris V440 keeps crashing

Hi, I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file. ... (1 Reply)
Discussion started by: samnyc
1 Replies

9. UNIX for Dummies Questions & Answers

How to Change the % prompt to - prompt in UNIX?

how to Change the % prompt to - prompt in unix :wall: ---------- Post updated at 07:40 AM ---------- Previous update was at 07:38 AM ---------- How To display the last modification time of any file in unix ---------- Post updated at 07:40 AM ---------- Previous update was at 07:40 AM... (2 Replies)
Discussion started by: manjiri sawant
2 Replies

10. Solaris

Unable to move from rsc prompt to ok prompt

Hi, on sunfire v890 unable to move from rsc prompt to ok prompt, i have executed the command break. (9 Replies)
Discussion started by: manoj.solaris
9 Replies
XHPPrompt(3X)															     XHPPrompt(3X)

NAME
XHPPrompt - Send a prompt to an extended input device. SYNOPSIS
#include <X11/XHPlib.h> int XHPPrompt (display, deviceid, prompt) Display *display; XID deviceid; unsigned int prompt; ARGUMENTS
display Specifies the connection to the X server. deviceid Specifies the ID of the desired device. Prompt Specifies the Prompt to be sent. Valid values are: GENERAL_PROMPT, PROMPT_1, PROMPT_2, PROMPT_3, PROMPT_4, PROMPT_5, PROMPT_6, PROMPT_7. DESCRIPTION
This request is part of an HP-proprietary extension to X. Its functionality has been superseded by the standard X input device extension XChangeFeedbackControl request. You should use XChangeFeedbackControl instead of XHPPrompt if possible. This request sends a prompt to an input device. A prompt is an audio or visual indication that the program controlling the input device is ready for input. The program may indicate that status by turning on a prompt on the appropriate input device. Not all input devices support prompts and acknowledges. Any device that does support a particular prompt will also support the corresponding acknowledge. To determine whether an input device supports a particular prompt and acknowledge, the io_byte field of the XHPDeviceList structure should be examined. The format of this structure is described in the documentation for the XHPListInputDevices request. RETURN VALUE
none DIAGNOSTICS
BadDevice An invalid device ID was specified. BadValue An invalid prompt was specified. FILES
/usr/include/X11/XHPlib.h ORIGIN
Hewlett-Packard Company SEE ALSO
XHPListInputDevices(3x) XHPAcknowledge(3x) X Version 11 Release 5 XHPPrompt(3X)
All times are GMT -4. The time now is 06:31 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy