01-23-2008
box[root]# ndd -get /dev/ce \?
? (read only)
instance (read and write)
adv_autoneg_cap (read and write)
adv_1000fdx_cap (read and write)
adv_1000hdx_cap (read and write)
adv_100T4_cap (read and write)
adv_100fdx_cap (read and write)
adv_100hdx_cap (read and write)
adv_10fdx_cap (read and write)
adv_10hdx_cap (read and write)
adv_asmpause_cap (read and write)
adv_pause_cap (read and write)
master_cfg_enable (read and write)
master_cfg_value (read and write)
use_int_xcvr (read and write)
enable_ipg0 (read and write)
ipg0 (read and write)
ipg1 (read and write)
ipg2 (read and write)
rx_intr_pkts (read and write)
rx_intr_time (read and write)
red_dv4to6k (read and write)
red_dv6to8k (read and write)
red_dv8to10k (read and write)
red_dv10to12k (read and write)
tx_dma_weight (read and write)
rx_dma_weight (read and write)
infinite_burst (read and write)
disable_64bit (read and write)
accept_jumbo (read and write)
laggr_multistream (read and write)
/dev/ce adv_10hdx_cap -- half dup
/dev/ce adv_10fdx_cap --full dup
box[root]# ndd -get /dev/ce adv_10hdx_cap
0
box[root]# ndd -get /dev/ce adv_10fdx_cap
0
use ndd to set it to 1, read man pages how to use ndd. Then add the ndd command into S99ndd in rc3.d so everything it reboot it will set to 10m
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
4. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Red Hat
I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ???
Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies
7. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
LEARN ABOUT OSF1
tis_rwlock_init
tis_rwlock_init(3) Library Functions Manual tis_rwlock_init(3)
NAME
tis_rwlock_init - Initializes a read-write lock object.
LIBRARY
Standard C Library (libc.so, libc.a)
SYNOPSIS
#include <tis.h>
int tis_rwlock_init(
tis_rwlock_t *lock);
STANDARDS
None
PARAMETERS
Address of a read-write lock object.
DESCRIPTION
This routine initializes a read-write lock object. The routine initializes the tis_rwlock_t structure that holds the object's lock states.
To destroy a read-write lock object, call the tis_rwlock_destroy(3) routine.
NOTE: The tis read-write lock has no relationship to the Single UNIX Specification, Version 2 (SUSV2, or UNIX98) read-write lock routines
(pthread_rwlock_init(3), etc). The tis_rwlock_t type, in particular, cannot be used with the pthread read-write lock functions; nor can a
pthread_rwlock_t type be used with the tis read-write lock functions.
RETURN VALUES
If an error condition occurs, this routine returns an integer value indicating the type of error. Possible return values are as follows:
Successful completion. The value specified by lock is not a valid read-write lock. Insufficient memory exists to initialize lock.
ERRORS
None
RELATED INFORMATION
Functions: tis_read_lock(3), tis_read_trylock(3), tis_read_unlock(3), tis_rwlock_destroy(3), tis_write_lock(3), tis_write_trylock(3),
tis_write_unlock(3)
Manuals: Guide to DECthreads and Programmer's Guide delim off
tis_rwlock_init(3)