01-23-2008
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
4. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Red Hat
I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ???
Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies
7. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
IPTRAF(8) System Manager's Manual IPTRAF(8)
NAME
iptraf - Interactive Colorful IP LAN Monitor
SYNOPSIS
iptraf { [ -f ] [ -q ] [ { -i iface | -g | -d iface | -s iface | -z iface | -l iface } [ -t timeout ] [ -B [ -L logfile ] ] ] | [ -h ] }
DESCRIPTION
iptraf is an ncurses-based IP LAN monitor that generates various network statistics including TCP info, UDP counts, ICMP and OSPF informa-
tion, Ethernet load info, node stats, IP checksum errors, and others.
If the command is issued without any command-line options, the program comes up in interactive mode, with the various facilities accessed
through the main menu.
OPTIONS
These options can also be supplied to the command:
-i iface
immediately start the IP traffic monitor on the specified interface, or all interfaces if "-i all" is specified
-g immediately start the general interface statistics
-d iface
allows you to immediately start the detailed on the indicated interface (iface)
-s iface
allows you to immediately monitor TCP and UDP traffic on the specified interface (iface)
-z iface
shows packet counts by size on the specified interface
-l iface
start the LAN station monitor on the specified interface, or all LAN interfaces if "-l all" is specified
-t timeout
tells IPTraf to run the specified facility for only timeout minutes. This option is used only with one of the above parameters.
-B redirect standard output to /dev/null, closes standard input, and forks the program into the background. Can be used only with one
of the facility invocation parameters above. Send the backgrounded process a USR2 signal to terminate.
-L logfile
allows you to specify an alternate log file name. The default log file name is based on either the interface selected (detailed
interface statistics, TCP/UDP service statistics, packet size breakdown), or the instance of the facility (IP traffic monitor, LAN
station monitor). If a path is not specified, the log file is placed in /var/log/iptraf
-f clears all locks and counters, causing this instance of IPTraf to think it's the first one running. This should only be used to
recover from an abnormal termination or system crash.
-q no longer needed, maintained only for compatibility.
-h shows a command summary
SIGNALS
SIGUSR1 - rotates log files while program is running
SIGUSR2 - terminates an IPTraf process running in the background.
FILES
/var/log/iptraf/*.log - log file
/var/local/iptraf/* - important IPTraf data files
SEE ALSO
Documentation/* - complete documentation written by the author
AUTHOR
Gerard Paul Java (riker@mozcom.com)
MANUAL AUTHOR
Frederic Peters (fpeters@debian.org), using iptraf --help General manual page modifications by Gerard Paul Java (riker@mozcom.com)
IPTraf Help Page IPTRAF(8)