Sponsored Content
Operating Systems Solaris How to force the LAN interface running on 10M Post 302160867 by DukeNuke2 on Wednesday 23rd of January 2008 01:53:29 AM
Old 01-23-2008
use this script:
http://docs.cirkva.net/Sun/Solaris/Eis/S68net-tune
read the first few lines on how to use it!
 

9 More Discussions You Might Find Interesting

1. Solaris

How to configure private LAN and coporate LAN on the same machine-Solaris10

Hi , I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10. How can I achieve this? Thanks (1 Reply)
Discussion started by: deedee
1 Replies

2. UNIX for Advanced & Expert Users

Double question: Apache mod_proxy and force connection over specific interface

Double question here ... Running on Debian Etch and Apache 2.0 1) Using mod_proxy and/or mod_proxy_http in apache 2.0. The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies

3. IP Networking

Solaris 9 new pumbed interface will not enter a RUNNING state

I'm trying to plumb a new interface bge1 on my machine: root@obms2-com-indianapolis-in:/root# ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet... (3 Replies)
Discussion started by: R37ribution
3 Replies

4. Solaris

how to force e1000g0 interface in solaris 10

Hi all, I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot. But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands. ... (1 Reply)
Discussion started by: mailbox80
1 Replies

5. IP Networking

Local Lan, no-ip directed DNS forward, surf within lan

Hi, We have a website running on a local centos 5.4 surfer, static IP. The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server. My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine. However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies

6. Red Hat

blue screen to config lan interface

I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ??? Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies

7. Red Hat

iptable port forwarding between two lan interface

Hi, How can I config iptables to allow port forwarding from one WAN interface to second lan interface . In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1) I want to make port forward port no 22 from 61.93.204.56 to port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

9. Solaris

Interface e1000g0 not showing in running state

Hello all, I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0. This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help. Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.12.1 2008-04-04 URI::URL(3)
All times are GMT -4. The time now is 11:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy