01-23-2008
How to force the LAN interface running on 10M
Hi all,
I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks!
9 More Discussions You Might Find Interesting
1. Solaris
Hi ,
I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10.
How can I achieve this?
Thanks (1 Reply)
Discussion started by: deedee
1 Replies
2. UNIX for Advanced & Expert Users
Double question here ... Running on Debian Etch and Apache 2.0
1) Using mod_proxy and/or mod_proxy_http in apache 2.0.
The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies
3. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
4. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
5. IP Networking
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies
6. Red Hat
I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ???
Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies
7. Red Hat
Hi,
How can I config iptables to allow port forwarding from one WAN interface to second lan interface .
In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1)
I want to make port forward port no 22 from 61.93.204.56 to
port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
LEARN ABOUT CENTOS
opensc-tool
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)