Sponsored Content
Full Discussion: Controller target disk?
Operating Systems Solaris Controller target disk? Post 302159965 by 1jnike on Saturday 19th of January 2008 05:24:29 PM
Old 01-19-2008
Java

Hi sudhir_shet,

I think you already have the control ids listed, the LiD & Port WWN you'll find are unique.

Before running any commands always check your man pages for backround & detailed information;

<snip start>
bash-2.05$ man format
Reformatting page. Please Wait... done

System Administration Commands

NAME
format - disk partitioning and maintenance utility
<snip end>


I believe the system is using FC-AL fibre disks, if you can boot the system to run solaris;

run the command

(As root or with root permission)

# format

(This will provide you with a list of attached disks & solaris control ids)

I hope this is of help

Jnike
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

The hard disk at channel 2, target 1 had a soft error.

Hi there! I received the following error message The hard disk at channel 2, target 1 had a soft error. The output of a system check reveiled the following (see entry <2,1> ): SWXCR xcr0 error counters: RAID Array 200 Controller Family Information Utility V1.03... (1 Reply)
Discussion started by: Ivo
1 Replies

2. SCO

Warning HD: no root disk controller was found

hi... i hav a problem to install sco unix while installing sco unix 5.0.5 in acer altos with hardware raid am getting error "Warning HD: no root disk controller was found system error 5: while getting fs type flushing controller: DAC960PRL cache done." i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies

3. HP-UX

[Joy Share] - Replace an unknown status controller on HP FC60 disk array

Replace an unknown status controller on HP FC60 disk array Author:JoyOnline JoyChangLu@gmail.com Trouble description: The users detected that the status of controller at A is unknown. Analysis and diagnostic: Physical observed all leds on enclosure of disk array is normal. The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies

4. SCO

SCO 5.0.7 no root disk controller found error during install

I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd. I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies

5. Solaris

Help needed to find out the disk controller for veritas disks

hi all i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output # vxdisk list DEVICE TYPE DISK GROUP STATUS c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies

6. SCO

Change Disk controller in SCO 6.0.0

So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller. First, I downloaded the megasas driver from SCO and installed it on the old system. Then I created a new Microlite Edge emergency boot cd with the new driver on it. I... (2 Replies)
Discussion started by: jgt
2 Replies

7. Solaris

Changed disk controller -> drops into GRUB?!

I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all. How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies

8. Solaris

Disk controller reassignment

Hi The scenario in the oracle t4-1 hardware with solaris 10 is as follows: 1. The initial install on the server was performed with an incorrect disk layout. 2. New disks were ordered and slot into the server. 3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies

9. Solaris

Use 'dd' to copy boot disk to larger target disk

Hi, I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
vxdiskadd(1M)															     vxdiskadd(1M)

NAME
vxdiskadd - add one or more disks for use with Veritas Volume Manager SYNOPSIS
vxdiskadd disk_address_pattern_list DESCRIPTION
The vxdiskadd utility configures disks for use by Veritas Volume Manager (VxVM). Disks must already have been formatted. vxdiskadd prompts the user for a disk group name and disk name for the disks. If no disk group name specified, the disks will be left as unassigned replacement disks for future use. A new disk group may be created that will become the disks' disk group. If a disk group is specified for the disks, the user is prompted for whether the disks should be designated as spares for the disk group. For new disks, all space on the disk becomes free space in the disk's disk group. vxdiskadd interactively allows initialization to be done for all the disks specified or allows the user to ask to make the decision for each disk individually. One or more disks may be specified with a disk_address_pattern_list. The basic form of a disk address is c#t#d#. Any leading portion of this address may be specified to indicate that all disks that match that leading portion should be used. For example c2t0 may be used to specify all disks on controller 2, target 0. More than one disk address or address pattern may be specified on the command line. In case of enclosure-based names, the disk address will be of the form enclosurename_diskno. The enclosurename indicates that all disks in the specified enclosure are used. For example, emc1_ is used to specify all disks in the enclosure emc1. The word all may be used to specify all disks on the system. Disk address names relate directly to device node names in the /dev/dmp and /dev/rdmp directories. Here are more examples: all: all disks c3 c4t2: all disks on controller 3 and controller 4, target 2 c3t4d2: a single disk (in the c#t#d# naming scheme) xyz_0 : a single disk (in the enclosure based naming scheme) xyz_ : all disks on the enclosure whose name is xyz The files /etc/vx/cntrls.exclude, /etc/vx/disks.exclude and /etc/vx/enclr.exclude may be used to exclude controllers or disks from use by vxdiskadd. Each line of cntrls.exclude specifies the address of a controller to exclude, for example, c2. Each line of disks.exclude spec- ifies a disk to exclude, for example, c0t3d0. Each line of enclr.exclude specifies the name of an enclosure to exclude, for example, enc0. All courses of action that do not involve clear failure conditions require prompts from the user, with defaults supplied as appropriate. Help is made available at every prompt. Entering ? in response to a prompt displays a context-sensitive help message. OPERATIONS
Reconnecting a drive that was temporarily inaccessible This situation is detected automatically by noting that the specified drive has a disk ID that matches a disk media record with no currently associated physical disk. After reconnection, any stale plexes referring the disk are reattached, and any stopped volumes referring the disk are restarted. This reattach action is performed by calling the vxrecover utility. Initialization of a disk with reserved regions Initialization of the disk is performed by calling vxdisksetup. Adding a disk to an existing disk group This operation can be performed independently of the initialization of the disk drive. The operation adds the disk to the group so that its storage is added to the free space pool in that disk group. The vxassist utility can subsequently allocate from that free space. Creation of new disk groups in which to import a new disk If disks are added that are required to be put into a disk group that does not exist, the option of creating the disk group is offered. Hardware-Specific Note Some environments provide guidelines to optimize VxVM's interaction with intelligent storage systems. If these guidelines are present, VxVM follows the guidelines when adding disks to disk groups. If the operation fails due to these guideline(s), you are prompted to use the force option. The force option ignores any such storage-specific guidelines. FILES
/etc/vx/cntrls.exclude Specifies the address of controllers to exclude from vxdiskadd operations. /etc/vx/disks.exclude Specifies the address of disks to exclude from vxdiskadd operations. /etc/vx/enclr.exclude Specifies the address of enclosures to exclude from vxdiskadd operations. NOTES
EFI disks cannot be added to a disk group that is compatible with the Cross-platform Data Sharing (CDS) feature, nor can they be formatted as CDS disks. SEE ALSO
vxassist(1M), vxdisk(1M), vxdiskadm(1M), vxdisksetup(1M), vxintro(1M), vxrecover(1M) VxVM 5.0.31.1 24 Mar 2008 vxdiskadd(1M)
All times are GMT -4. The time now is 06:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy